1993–1995 Mazda RX-7 Wheel & Tire Fitment Guide
FD generation, R1. 5x114.3 bolt pattern, stock 16×8 ET50 on 225/50R16. Compare 2 popular upgrades or try your own size.
Specs
| Bolt pattern | 5x114.3 |
|---|---|
| Center bore | 67.1 mm |
| Lug thread | M12x1.5 |
| Reference trim | R1 |
| Stock wheel | 16×8 ET50 |
| Stock tire | 225/50R16 |
| Stock overall diameter | 24.86 in |
Calculator
Starts on the stock setup. Drag the sliders or load one of the popular upgrades below.
The small mark on each slider shows the current value. Type in the box for sizes outside the slider range.
Custom vehicle measurementsOptional
Measure with your current wheels on the car and the results below show how much room the new setup leaves. The drawings use your numbers too. Leave blank anything you haven't measured.
- Park on level ground at normal ride height, wheels straight.
- Front and rear differ. Measure the axle you're changing, or enter the tighter corner.
Millimetres or centimetres are recommended: small gaps are easier to read accurately than inch marks.
Narrowest gap between the inside of the tire (or wheel, whichever sits further in) and the strut, spring perch or upper control arm. Wheels pointed straight.
Hang a plumb line or hold a straightedge vertically from the fender lip above the hub, then measure across to the outermost point of the tire or wheel. Enter a negative number if it already sticks out.
Straight up from the top of the tire to the fender lip, with the car on the ground at normal ride height.
Smallest gap between the outer edge of the brake caliper and the inside of the wheel barrel.
- Poke
- 0mm
- Wheel face stays where it is.
- Inner clearance
- 0mm
- Same room to the suspension.
- Overall diameter
- 0%
- 0 in, within ±3%.
- Speedo reads 60
- 60mph
- Your actual speed.
| Vehicle | Mazda RX-7 R1 | ||
|---|---|---|---|
| Bolt pattern | 5x114.3 | Hub bore | 67.1 mm |
| Current | 16×8 ET50, 225/50R16 | New | 16×8 ET50, 225/50R16 |
Popular upgrades
Each size compared with the stock 16×8 ET50, 225/50R16.
| Setup | Poke | Inner clearance | Diameter | Speedo reads 60 | Action |
|---|---|---|---|---|---|
| Flush 17×9.517×9.5 ET51, 255/40R17 | +18 mm | −20 mm | +0.7% | 60.4 mph | |
| Wide 17×917×9 ET35, 255/40R17 | +27.7 mm | +2.3 mm | +0.7% | 60.4 mph |
Notes
- US cars (base, Touring, R1/R2) all ran square 16×8 ET50 wheels with 225/50ZR16 tires.
- Every factory FD wheel is ET50, including the later JDM 17s (17×8 front / 17×8.5 rear with 235/45R17 and 255/40R17) that are a common OEM-plus swap.
- Early 16-in wheels were prone to cracking; Mazda revised them with thicker walls, so check used OEM wheels for the reinforced version.
- 17×9.5 ET51 with 255/40R17 fits under stock fenders, but plan on about −2° camber and possibly rolled fenders at lower ride heights.
Questions
What bolt pattern does a 1993–1995 Mazda RX-7 use?
The 1993–1995 Mazda RX-7 uses a 5x114.3 bolt pattern with a 67.1 mm center bore and M12x1.5 lug threads.
What size wheels and tires are stock on the 1993–1995 Mazda RX-7 R1?
The 1993–1995 Mazda RX-7 R1 came with 16×8 ET50 wheels and 225/50R16 tires, about 24.9 inches in overall diameter.
How far does a 17×9 ET35 wheel stick out on a 1993–1995 Mazda RX-7?
On the 1993–1995 Mazda RX-7, compared with the stock 16×8 ET50, a 17×9 ET35 sits 27.7 mm further out at the outer lip and 2.3 mm further from the suspension at the inner barrel.
Which 1993–1995 Mazda RX-7 wheel and tire upgrade keeps the speedometer most accurate?
Of the 1993–1995 Mazda RX-7 upgrades listed here, 17×9.5 ET51 · 255/40R17 is closest to the stock 225/50R16, changing overall diameter by +0.7%. At an indicated 60 mph you would actually be doing 60.4 mph.
Do aftermarket wheels need hub-centric rings on a 1993–1995 Mazda RX-7?
The 1993–1995 Mazda RX-7's hub bore is 67.1 mm. Wheels machined to exactly 67.1 mm center on the hub directly; wheels with a larger bore need 67.1 mm hub-centric rings to avoid vibration.
Also on 5x114.3
These share the bolt pattern. Check offset, hub bore and brake clearance before swapping wheels.
| Vehicle | Generation | Bolt pattern | Hub bore |
|---|---|---|---|
| 2010–2013 Mazda Mazdaspeed3 | BL | 5x114.3 | 67.1 mm |
| 2019+ Genesis G70 | 1st gen (IK) | 5x114.3 | 67.1 mm |
| 2018–2023 Kia Stinger | CK | 5x114.3 | 67.1 mm |
| 2003–2006 Mitsubishi Lancer Evolution | VIII/IX (CT9A) | 5x114.3 | 67.1 mm |
| 2008–2015 Mitsubishi Lancer Evolution | X | 5x114.3 | 67.1 mm |
| 2025+ Hyundai Ioniq 5 N | NE | 5x114.3 | 67.1 mm |