2010–2013 Mazda Mazdaspeed3 Wheel & Tire Fitment Guide
BL generation, Touring. 5x114.3 bolt pattern, stock 18×7.5 ET52.5 on 225/40R18. Compare 2 popular upgrades or try your own size.
Specs
| Bolt pattern | 5x114.3 |
|---|---|
| Center bore | 67.1 mm |
| Lug thread | M12x1.5 |
| Reference trim | Touring |
| Stock wheel | 18×7.5 ET52.5 |
| Stock tire | 225/40R18 |
| Stock overall diameter | 25.09 in |
Calculator
Starts on the stock setup. Drag the sliders or load one of the popular upgrades below.
The small mark on each slider shows the current value. Type in the box for sizes outside the slider range.
Custom vehicle measurementsOptional
Measure with your current wheels on the car and the results below show how much room the new setup leaves. The drawings use your numbers too. Leave blank anything you haven't measured.
- Park on level ground at normal ride height, wheels straight.
- Front and rear differ. Measure the axle you're changing, or enter the tighter corner.
Millimetres or centimetres are recommended: small gaps are easier to read accurately than inch marks.
Narrowest gap between the inside of the tire (or wheel, whichever sits further in) and the strut, spring perch or upper control arm. Wheels pointed straight.
Hang a plumb line or hold a straightedge vertically from the fender lip above the hub, then measure across to the outermost point of the tire or wheel. Enter a negative number if it already sticks out.
Straight up from the top of the tire to the fender lip, with the car on the ground at normal ride height.
Smallest gap between the outer edge of the brake caliper and the inside of the wheel barrel.
- Poke
- 0mm
- Wheel face stays where it is.
- Inner clearance
- 0mm
- Same room to the suspension.
- Overall diameter
- 0%
- 0 in, within ±3%.
- Speedo reads 60
- 60mph
- Your actual speed.
| Vehicle | Mazda Mazdaspeed3 Touring | ||
|---|---|---|---|
| Bolt pattern | 5x114.3 | Hub bore | 67.1 mm |
| Current | 18×7.5 ET52.5, 225/40R18 | New | 18×7.5 ET52.5, 225/40R18 |
Popular upgrades
Each size compared with the stock 18×7.5 ET52.5, 225/40R18.
| Setup | Poke | Inner clearance | Diameter | Speedo reads 60 | Action |
|---|---|---|---|---|---|
| Mild 18×818×8 ET48, 235/40R18 | +10.8 mm | −1.8 mm | +1.3% | 60.8 mph | |
| Wide 18×9.518×9.5 ET38, 235/40R18 | +39.9 mm | −10.9 mm | +1.3% | 60.8 mph |
Notes
- Sport and Touring share the same 18×7.5 ET52.5 OEM wheel (silver or charcoal) with 225/40R18 tires.
- Wider tires usually rub on the forward lip of the rear fenders. Owners report the fronts are effectively already rolled from the factory, so the rears are what get rolled.
- 18×9.5 around ET35–38 typically needs rolled fenders and often coilovers to avoid rubbing at full compression.
Questions
What bolt pattern does a 2010–2013 Mazda Mazdaspeed3 use?
The 2010–2013 Mazda Mazdaspeed3 uses a 5x114.3 bolt pattern with a 67.1 mm center bore and M12x1.5 lug threads.
What size wheels and tires are stock on the 2010–2013 Mazda Mazdaspeed3 Touring?
The 2010–2013 Mazda Mazdaspeed3 Touring came with 18×7.5 ET52.5 wheels and 225/40R18 tires, about 25.1 inches in overall diameter.
How far does a 18×9.5 ET38 wheel stick out on a 2010–2013 Mazda Mazdaspeed3?
On the 2010–2013 Mazda Mazdaspeed3, compared with the stock 18×7.5 ET52.5, a 18×9.5 ET38 sits 39.9 mm further out at the outer lip and 10.9 mm closer to the suspension at the inner barrel.
Which 2010–2013 Mazda Mazdaspeed3 wheel and tire upgrade keeps the speedometer most accurate?
Of the 2010–2013 Mazda Mazdaspeed3 upgrades listed here, 18×8 ET48 · 235/40R18 is closest to the stock 225/40R18, changing overall diameter by +1.3%. At an indicated 60 mph you would actually be doing 60.8 mph.
Do aftermarket wheels need hub-centric rings on a 2010–2013 Mazda Mazdaspeed3?
The 2010–2013 Mazda Mazdaspeed3's hub bore is 67.1 mm. Wheels machined to exactly 67.1 mm center on the hub directly; wheels with a larger bore need 67.1 mm hub-centric rings to avoid vibration.
Also on 5x114.3
These share the bolt pattern. Check offset, hub bore and brake clearance before swapping wheels.
| Vehicle | Generation | Bolt pattern | Hub bore |
|---|---|---|---|
| 1993–1995 Mazda RX-7 | FD | 5x114.3 | 67.1 mm |
| 2019+ Genesis G70 | 1st gen (IK) | 5x114.3 | 67.1 mm |
| 2018–2023 Kia Stinger | CK | 5x114.3 | 67.1 mm |
| 2003–2006 Mitsubishi Lancer Evolution | VIII/IX (CT9A) | 5x114.3 | 67.1 mm |
| 2008–2015 Mitsubishi Lancer Evolution | X | 5x114.3 | 67.1 mm |
| 2025+ Hyundai Ioniq 5 N | NE | 5x114.3 | 67.1 mm |