2018–2023 Kia Stinger Wheel & Tire Fitment Guide
CK generation, GT. 5x114.3 bolt pattern, stock 19×8 ET34 on 225/40R19. Compare 3 popular upgrades or try your own size.
Specs
| Bolt pattern | 5x114.3 |
|---|---|
| Center bore | 67.1 mm |
| Lug thread | M12x1.5 |
| Reference trim | GT |
| Stock wheel | 19×8 ET34 |
| Stock tire | 225/40R19 |
| Stock overall diameter | 26.09 in |
Calculator
Starts on the stock setup. Drag the sliders or load one of the popular upgrades below.
The small mark on each slider shows the current value. Type in the box for sizes outside the slider range.
Custom vehicle measurementsOptional
Measure with your current wheels on the car and the results below show how much room the new setup leaves. The drawings use your numbers too. Leave blank anything you haven't measured.
- Park on level ground at normal ride height, wheels straight.
- Front and rear differ. Measure the axle you're changing, or enter the tighter corner.
Millimetres or centimetres are recommended: small gaps are easier to read accurately than inch marks.
Narrowest gap between the inside of the tire (or wheel, whichever sits further in) and the strut, spring perch or upper control arm. Wheels pointed straight.
Hang a plumb line or hold a straightedge vertically from the fender lip above the hub, then measure across to the outermost point of the tire or wheel. Enter a negative number if it already sticks out.
Straight up from the top of the tire to the fender lip, with the car on the ground at normal ride height.
Smallest gap between the outer edge of the brake caliper and the inside of the wheel barrel.
- Poke
- 0mm
- Wheel face stays where it is.
- Inner clearance
- 0mm
- Same room to the suspension.
- Overall diameter
- 0%
- 0 in, within ±3%.
- Speedo reads 60
- 60mph
- Your actual speed.
| Vehicle | Kia Stinger GT | ||
|---|---|---|---|
| Bolt pattern | 5x114.3 | Hub bore | 67.1 mm |
| Current | 19×8 ET34, 225/40R19 | New | 19×8 ET34, 225/40R19 |
Popular upgrades
Each size compared with the stock 19×8 ET34, 225/40R19.
| Setup | Poke | Inner clearance | Diameter | Speedo reads 60 | Action |
|---|---|---|---|---|---|
| 19×8.5 +40 staggered19×8.5 ET40, 225/40R19 | +0.3 mm | −12.3 mm | 0% | 60 mph | |
| 19×8.5 +35 wider19×8.5 ET35, 235/40R19 | +5.3 mm | −7.3 mm | +1.2% | 60.7 mph | |
| 20×9 +35 staggered20×9 ET35, 245/35R20 | +11.7 mm | −13.7 mm | +2.6% | 61.5 mph |
Notes
- Rear stock is 19×8.5 ET46.5 with 255/35R19. The GT is staggered with the same sizes on RWD and AWD.
- The GT's Brembo brakes (350 mm front rotors, 4-piston calipers) need 19 in wheels at minimum. The 2.0T's single-piston brakes clear 18s, and it comes on 18×8 ET34 all around.
- Low offsets (+15 to +25) can put the spokes against the Brembo calipers, so those setups often need 5–10 mm spacers.
- Common aftermarket staggers are 19×8.5/19×9.5 with 225/40R19 and 255/35R19, and 20×9/20×10.5 with 245/35R20 and 285/30R20.
Questions
What bolt pattern does a 2018–2023 Kia Stinger use?
The 2018–2023 Kia Stinger uses a 5x114.3 bolt pattern with a 67.1 mm center bore and M12x1.5 lug threads.
What size wheels and tires are stock on the 2018–2023 Kia Stinger GT?
The 2018–2023 Kia Stinger GT came with 19×8 ET34 wheels and 225/40R19 tires, about 26.1 inches in overall diameter.
How far does a 20×9 ET35 wheel stick out on a 2018–2023 Kia Stinger?
On the 2018–2023 Kia Stinger, compared with the stock 19×8 ET34, a 20×9 ET35 sits 11.7 mm further out at the outer lip and 13.7 mm closer to the suspension at the inner barrel.
Which 2018–2023 Kia Stinger wheel and tire upgrade keeps the speedometer most accurate?
Of the 2018–2023 Kia Stinger upgrades listed here, 19×8.5 ET40 · 225/40R19 is closest to the stock 225/40R19, changing overall diameter by 0%. At an indicated 60 mph you would actually be doing 60 mph.
Do aftermarket wheels need hub-centric rings on a 2018–2023 Kia Stinger?
The 2018–2023 Kia Stinger's hub bore is 67.1 mm. Wheels machined to exactly 67.1 mm center on the hub directly; wheels with a larger bore need 67.1 mm hub-centric rings to avoid vibration.
Also on 5x114.3
These share the bolt pattern. Check offset, hub bore and brake clearance before swapping wheels.
| Vehicle | Generation | Bolt pattern | Hub bore |
|---|---|---|---|
| 2019+ Genesis G70 | 1st gen (IK) | 5x114.3 | 67.1 mm |
| 2010–2013 Mazda Mazdaspeed3 | BL | 5x114.3 | 67.1 mm |
| 1993–1995 Mazda RX-7 | FD | 5x114.3 | 67.1 mm |
| 2003–2006 Mitsubishi Lancer Evolution | VIII/IX (CT9A) | 5x114.3 | 67.1 mm |
| 2008–2015 Mitsubishi Lancer Evolution | X | 5x114.3 | 67.1 mm |
| 2025+ Hyundai Ioniq 5 N | NE | 5x114.3 | 67.1 mm |