2020+ Chevrolet Corvette Wheel & Tire Fitment Guide
C8 generation, Stingray Z51. 5x120 bolt pattern, stock 19×8.5 ET52 on 245/35R19. Compare 2 popular upgrades or try your own size.
Specs
| Bolt pattern | 5x120 |
|---|---|
| Center bore | 66.9 mm |
| Lug thread | M14x1.5 |
| Reference trim | Stingray Z51 |
| Stock wheel | 19×8.5 ET52 |
| Stock tire | 245/35R19 |
| Stock overall diameter | 25.75 in |
Calculator
Starts on the stock setup. Drag the sliders or load one of the popular upgrades below.
The small mark on each slider shows the current value. Type in the box for sizes outside the slider range.
Custom vehicle measurementsOptional
Measure with your current wheels on the car and the results below show how much room the new setup leaves. The drawings use your numbers too. Leave blank anything you haven't measured.
- Park on level ground at normal ride height, wheels straight.
- Front and rear differ. Measure the axle you're changing, or enter the tighter corner.
Millimetres or centimetres are recommended: small gaps are easier to read accurately than inch marks.
Narrowest gap between the inside of the tire (or wheel, whichever sits further in) and the strut, spring perch or upper control arm. Wheels pointed straight.
Hang a plumb line or hold a straightedge vertically from the fender lip above the hub, then measure across to the outermost point of the tire or wheel. Enter a negative number if it already sticks out.
Straight up from the top of the tire to the fender lip, with the car on the ground at normal ride height.
Smallest gap between the outer edge of the brake caliper and the inside of the wheel barrel.
- Poke
- 0mm
- Wheel face stays where it is.
- Inner clearance
- 0mm
- Same room to the suspension.
- Overall diameter
- 0%
- 0 in, within ±3%.
- Speedo reads 60
- 60mph
- Your actual speed.
| Vehicle | Chevrolet Corvette Stingray Z51 | ||
|---|---|---|---|
| Bolt pattern | 5x120 | Hub bore | 66.9 mm |
| Current | 19×8.5 ET52, 245/35R19 | New | 19×8.5 ET52, 245/35R19 |
Popular upgrades
Each size compared with the stock 19×8.5 ET52, 245/35R19.
| Setup | Poke | Inner clearance | Diameter | Speedo reads 60 | Action |
|---|---|---|---|---|---|
| OEM+ 19×919×9 ET36, 255/35R19 | +22.4 mm | +9.6 mm | +1.1% | 60.6 mph | |
| Track 18×1018×10 ET42, 275/35R18 | +29.1 mm | −9.1 mm | −0.7% | 59.6 mph |
Notes
- Rear stock: 20×11 ET64 with 305/30R20.
- The C8 switched to 5x120 with a 66.9 mm bore and M14x1.5 lug nuts, so C7 wheels (5x120.65, M12x1.5) do not bolt on.
- Apex's direct-fit OEM+ set is 19×9 ET36 front / 20×11.5 ET48 rear; their 18×10 ET42 front track setup needs at least -1.5° front camber.
- Z06, E-Ray and Grand Sport cars are widebody and use 19×10 / 20×12 wheels that are not a direct swap onto a Stingray.
Questions
What bolt pattern does a 2020+ Chevrolet Corvette use?
The 2020+ Chevrolet Corvette uses a 5x120 bolt pattern with a 66.9 mm center bore and M14x1.5 lug threads.
What size wheels and tires are stock on the 2020+ Chevrolet Corvette Stingray Z51?
The 2020+ Chevrolet Corvette Stingray Z51 came with 19×8.5 ET52 wheels and 245/35R19 tires, about 25.8 inches in overall diameter.
How far does a 18×10 ET42 wheel stick out on a 2020+ Chevrolet Corvette?
On the 2020+ Chevrolet Corvette, compared with the stock 19×8.5 ET52, a 18×10 ET42 sits 29.1 mm further out at the outer lip and 9.1 mm closer to the suspension at the inner barrel.
Which 2020+ Chevrolet Corvette wheel and tire upgrade keeps the speedometer most accurate?
Of the 2020+ Chevrolet Corvette upgrades listed here, 18×10 ET42 · 275/35R18 is closest to the stock 245/35R19, changing overall diameter by −0.7%. At an indicated 60 mph you would actually be doing 59.6 mph.
Do aftermarket wheels need hub-centric rings on a 2020+ Chevrolet Corvette?
The 2020+ Chevrolet Corvette's hub bore is 66.9 mm. Wheels machined to exactly 66.9 mm center on the hub directly; wheels with a larger bore need 66.9 mm hub-centric rings to avoid vibration.
Also on 5x120
These share the bolt pattern. Check offset, hub bore and brake clearance before swapping wheels.
| Vehicle | Generation | Bolt pattern | Hub bore |
|---|---|---|---|
| 2010–2015 Chevrolet Camaro | 5th gen | 5x120 | 66.9 mm |
| 2016–2024 Chevrolet Camaro | 6th gen | 5x120 | 66.9 mm |
| 2017–2024 Chevrolet Camaro | 6th gen | 5x120 | 66.9 mm |
| 2014–2017 Chevrolet SS | VF (Zeta) | 5x120 | 66.9 mm |
| 2022+ Cadillac CT5-V Blackwing | 1st gen | 5x120 | 66.9 mm |
| 2024+ Acura Integra | DE5 | 5x120 | 64.1 mm |