2017–2024 Chevrolet Camaro Wheel & Tire Fitment Guide
6th gen generation, ZL1. 5x120 bolt pattern, stock 20×10 ET20 on 285/30R20. Compare 2 popular upgrades or try your own size.
Specs
| Bolt pattern | 5x120 |
|---|---|
| Center bore | 66.9 mm |
| Lug thread | M14x1.5 |
| Reference trim | ZL1 |
| Stock wheel | 20×10 ET20 |
| Stock tire | 285/30R20 |
| Stock overall diameter | 26.73 in |
Calculator
Starts on the stock setup. Drag the sliders or load one of the popular upgrades below.
The small mark on each slider shows the current value. Type in the box for sizes outside the slider range.
Custom vehicle measurementsOptional
Measure with your current wheels on the car and the results below show how much room the new setup leaves. The drawings use your numbers too. Leave blank anything you haven't measured.
- Park on level ground at normal ride height, wheels straight.
- Front and rear differ. Measure the axle you're changing, or enter the tighter corner.
Millimetres or centimetres are recommended: small gaps are easier to read accurately than inch marks.
Narrowest gap between the inside of the tire (or wheel, whichever sits further in) and the strut, spring perch or upper control arm. Wheels pointed straight.
Hang a plumb line or hold a straightedge vertically from the fender lip above the hub, then measure across to the outermost point of the tire or wheel. Enter a negative number if it already sticks out.
Straight up from the top of the tire to the fender lip, with the car on the ground at normal ride height.
Smallest gap between the outer edge of the brake caliper and the inside of the wheel barrel.
- Poke
- 0mm
- Wheel face stays where it is.
- Inner clearance
- 0mm
- Same room to the suspension.
- Overall diameter
- 0%
- 0 in, within ±3%.
- Speedo reads 60
- 60mph
- Your actual speed.
| Vehicle | Chevrolet Camaro ZL1 | ||
|---|---|---|---|
| Bolt pattern | 5x120 | Hub bore | 66.9 mm |
| Current | 20×10 ET20, 285/30R20 | New | 20×10 ET20, 285/30R20 |
Popular upgrades
Each size compared with the stock 20×10 ET20, 285/30R20.
| Setup | Poke | Inner clearance | Diameter | Speedo reads 60 | Action |
|---|---|---|---|---|---|
| Flush 20×10.520×10.5 ET15, 285/30R20 | +11.3 mm | −1.3 mm | 0% | 60 mph | |
| Track square 19×1119×11 ET11, 305/30R19 | +21.7 mm | −3.7 mm | −2% | 58.8 mph |
Notes
- Rear stock: 20×11 ET43 with 305/30R20 (GM part 23355801; front is 23355790, 20×10 ET20).
- Factory lug nuts are M14x1.5 on a 66.9 mm hub; ZL1 1LE cars instead run 19-inch wheels (19×11 front, 19×12 rear), which shows 19s clear the ZL1 brakes.
- A 19×11 ET9-11 front with 305/30R19 fits on factory alignment, but adding negative camber with the factory adjustment needs a 3 mm spacer or strut grinding; aftermarket camber plates avoid both.
- The 20×10.5 ET15 front is usually paired with a 20×11.5 ET42 rear on 305/30R20.
Questions
What bolt pattern does a 2017–2024 Chevrolet Camaro use?
The 2017–2024 Chevrolet Camaro uses a 5x120 bolt pattern with a 66.9 mm center bore and M14x1.5 lug threads.
What size wheels and tires are stock on the 2017–2024 Chevrolet Camaro ZL1?
The 2017–2024 Chevrolet Camaro ZL1 came with 20×10 ET20 wheels and 285/30R20 tires, about 26.7 inches in overall diameter.
How far does a 19×11 ET11 wheel stick out on a 2017–2024 Chevrolet Camaro?
On the 2017–2024 Chevrolet Camaro, compared with the stock 20×10 ET20, a 19×11 ET11 sits 21.7 mm further out at the outer lip and 3.7 mm closer to the suspension at the inner barrel.
Which 2017–2024 Chevrolet Camaro wheel and tire upgrade keeps the speedometer most accurate?
Of the 2017–2024 Chevrolet Camaro upgrades listed here, 20×10.5 ET15 · 285/30R20 is closest to the stock 285/30R20, changing overall diameter by 0%. At an indicated 60 mph you would actually be doing 60 mph.
Do aftermarket wheels need hub-centric rings on a 2017–2024 Chevrolet Camaro?
The 2017–2024 Chevrolet Camaro's hub bore is 66.9 mm. Wheels machined to exactly 66.9 mm center on the hub directly; wheels with a larger bore need 66.9 mm hub-centric rings to avoid vibration.
Also on 5x120
These share the bolt pattern. Check offset, hub bore and brake clearance before swapping wheels.
| Vehicle | Generation | Bolt pattern | Hub bore |
|---|---|---|---|
| 2010–2015 Chevrolet Camaro | 5th gen | 5x120 | 66.9 mm |
| 2016–2024 Chevrolet Camaro | 6th gen | 5x120 | 66.9 mm |
| 2020+ Chevrolet Corvette | C8 | 5x120 | 66.9 mm |
| 2014–2017 Chevrolet SS | VF (Zeta) | 5x120 | 66.9 mm |
| 2022+ Cadillac CT5-V Blackwing | 1st gen | 5x120 | 66.9 mm |
| 2024+ Acura Integra | DE5 | 5x120 | 64.1 mm |