2020+ Toyota GR Supra Wheel & Tire Fitment Guide
A90/J29 generation, 3.0. 5x112 bolt pattern, stock 19×9 ET32 on 255/35R19. Compare 3 popular upgrades or try your own size.
Specs
| Bolt pattern | 5x112 |
|---|---|
| Center bore | 66.6 mm |
| Lug thread | M14x1.25 |
| Reference trim | 3.0 |
| Stock wheel | 19×9 ET32 |
| Stock tire | 255/35R19 |
| Stock overall diameter | 26.03 in |
Calculator
Starts on the stock setup. Drag the sliders or load one of the popular upgrades below.
The small mark on each slider shows the current value. Type in the box for sizes outside the slider range.
Custom vehicle measurementsOptional
Measure with your current wheels on the car and the results below show how much room the new setup leaves. The drawings use your numbers too. Leave blank anything you haven't measured.
- Park on level ground at normal ride height, wheels straight.
- Front and rear differ. Measure the axle you're changing, or enter the tighter corner.
Millimetres or centimetres are recommended: small gaps are easier to read accurately than inch marks.
Narrowest gap between the inside of the tire (or wheel, whichever sits further in) and the strut, spring perch or upper control arm. Wheels pointed straight.
Hang a plumb line or hold a straightedge vertically from the fender lip above the hub, then measure across to the outermost point of the tire or wheel. Enter a negative number if it already sticks out.
Straight up from the top of the tire to the fender lip, with the car on the ground at normal ride height.
Smallest gap between the outer edge of the brake caliper and the inside of the wheel barrel.
- Poke
- 0mm
- Wheel face stays where it is.
- Inner clearance
- 0mm
- Same room to the suspension.
- Overall diameter
- 0%
- 0 in, within ±3%.
- Speedo reads 60
- 60mph
- Your actual speed.
| Vehicle | Toyota GR Supra 3.0 | ||
|---|---|---|---|
| Bolt pattern | 5x112 | Hub bore | 66.6 mm |
| Current | 19×9 ET32, 255/35R19 | New | 19×9 ET32, 255/35R19 |
Popular upgrades
Each size compared with the stock 19×9 ET32, 255/35R19.
| Setup | Poke | Inner clearance | Diameter | Speedo reads 60 | Action |
|---|---|---|---|---|---|
| Mild 19×9.519×9.5 ET29, 265/35R19 | +9.3 mm | −3.3 mm | +1.1% | 60.6 mph | |
| Flush 19×9.519×9.5 ET22, 275/35R19 | +16.3 mm | +3.7 mm | +2.1% | 61.3 mph | |
| Track square 18×1018×10 ET32, 275/40R18 | +12.7 mm | −12.7 mm | +2.4% | 61.5 mph |
Notes
- Rear stock: 19×10 ET40 with 275/35R19 (forged wheels on the 3.0).
- The 2.0 (2021+) uses the same 5x112 hub with cast 18×9 ET32 front and 18×10 ET40 rear on 255/40R18 and 275/40R18.
- Wheels are held by M14x1.25 conical-seat lug bolts, not studs; the pattern is 5x112, not the 5x120 of older BMWs.
- Flush 19×9.5 ET22 front setups are reported rub-free at stock height; a 20 mm front / 15 mm rear spacer pairing is the common way to flush the stock wheels.
Questions
What bolt pattern does a 2020+ Toyota GR Supra use?
The 2020+ Toyota GR Supra uses a 5x112 bolt pattern with a 66.6 mm center bore and M14x1.25 lug threads.
What size wheels and tires are stock on the 2020+ Toyota GR Supra 3.0?
The 2020+ Toyota GR Supra 3.0 came with 19×9 ET32 wheels and 255/35R19 tires, about 26 inches in overall diameter.
How far does a 19×9.5 ET22 wheel stick out on a 2020+ Toyota GR Supra?
On the 2020+ Toyota GR Supra, compared with the stock 19×9 ET32, a 19×9.5 ET22 sits 16.3 mm further out at the outer lip and 3.7 mm further from the suspension at the inner barrel.
Which 2020+ Toyota GR Supra wheel and tire upgrade keeps the speedometer most accurate?
Of the 2020+ Toyota GR Supra upgrades listed here, 19×9.5 ET29 · 265/35R19 is closest to the stock 255/35R19, changing overall diameter by +1.1%. At an indicated 60 mph you would actually be doing 60.6 mph.
Do aftermarket wheels need hub-centric rings on a 2020+ Toyota GR Supra?
The 2020+ Toyota GR Supra's hub bore is 66.6 mm. Wheels machined to exactly 66.6 mm center on the hub directly; wheels with a larger bore need 66.6 mm hub-centric rings to avoid vibration.
Also on 5x112
These share the bolt pattern. Check offset, hub bore and brake clearance before swapping wheels.
| Vehicle | Generation | Bolt pattern | Hub bore |
|---|---|---|---|
| 2020+ BMW 3 Series | G20 | 5x112 | 66.6 mm |
| 2023+ BMW M2 | G87 | 5x112 | 66.6 mm |
| 2021+ BMW M3 | G80 | 5x112 | 66.6 mm |
| 2010–2016 Audi S4 | B8/B8.5 | 5x112 | 66.6 mm |
| 2000–2002 Audi S4 | B5 | 5x112 | 57.1 mm |
| 2018–2025 Audi S4 | B9 | 5x112 | 66.5 mm |