2010–2016 Audi S4 Wheel & Tire Fitment Guide
B8/B8.5 generation, Premium Plus. 5x112 bolt pattern, stock 18×8 ET47 on 245/40R18. Compare 3 popular upgrades or try your own size.
Specs
| Bolt pattern | 5x112 |
|---|---|
| Center bore | 66.6 mm |
| Lug thread | M14x1.5 |
| Reference trim | Premium Plus |
| Stock wheel | 18×8 ET47 |
| Stock tire | 245/40R18 |
| Stock overall diameter | 25.72 in |
Calculator
Starts on the stock setup. Drag the sliders or load one of the popular upgrades below.
The small mark on each slider shows the current value. Type in the box for sizes outside the slider range.
Custom vehicle measurementsOptional
Measure with your current wheels on the car and the results below show how much room the new setup leaves. The drawings use your numbers too. Leave blank anything you haven't measured.
- Park on level ground at normal ride height, wheels straight.
- Front and rear differ. Measure the axle you're changing, or enter the tighter corner.
Millimetres or centimetres are recommended: small gaps are easier to read accurately than inch marks.
Narrowest gap between the inside of the tire (or wheel, whichever sits further in) and the strut, spring perch or upper control arm. Wheels pointed straight.
Hang a plumb line or hold a straightedge vertically from the fender lip above the hub, then measure across to the outermost point of the tire or wheel. Enter a negative number if it already sticks out.
Straight up from the top of the tire to the fender lip, with the car on the ground at normal ride height.
Smallest gap between the outer edge of the brake caliper and the inside of the wheel barrel.
- Poke
- 0mm
- Wheel face stays where it is.
- Inner clearance
- 0mm
- Same room to the suspension.
- Overall diameter
- 0%
- 0 in, within ±3%.
- Speedo reads 60
- 60mph
- Your actual speed.
| Vehicle | Audi S4 Premium Plus | ||
|---|---|---|---|
| Bolt pattern | 5x112 | Hub bore | 66.6 mm |
| Current | 18×8 ET47, 245/40R18 | New | 18×8 ET47, 245/40R18 |
Popular upgrades
Each size compared with the stock 18×8 ET47, 245/40R18.
| Setup | Poke | Inner clearance | Diameter | Speedo reads 60 | Action |
|---|---|---|---|---|---|
| OEM+ 19×9.519×9.5 ET45, 255/35R19 | +21 mm | −17 mm | +1.2% | 60.7 mph | |
| Flush 19×9.519×9.5 ET35, 255/35R19 | +31 mm | −7 mm | +1.2% | 60.7 mph | |
| Wide 18×9.518×9.5 ET38, 265/35R18 | +28 mm | −10 mm | −1.6% | 59 mph |
Notes
- The optional OEM 19in wheel is 19x8.5 ET43 with 255/35R19.
- Uses M14x1.5 lug bolts (OEM 27mm ball seat); many aftermarket wheels are drilled for M12 or conical seats and need matching bolts or a conversion kit.
- S4 brakes are larger than A4 brakes; some 18in wheels need spacers or rear brake-bracket grinding to clear them.
- An owner on 19x9.5 ET35 with 255/35R19 reported rubbing only at full steering lock.
Questions
What bolt pattern does a 2010–2016 Audi S4 use?
The 2010–2016 Audi S4 uses a 5x112 bolt pattern with a 66.6 mm center bore and M14x1.5 lug threads.
What size wheels and tires are stock on the 2010–2016 Audi S4 Premium Plus?
The 2010–2016 Audi S4 Premium Plus came with 18×8 ET47 wheels and 245/40R18 tires, about 25.7 inches in overall diameter.
How far does a 19×9.5 ET35 wheel stick out on a 2010–2016 Audi S4?
On the 2010–2016 Audi S4, compared with the stock 18×8 ET47, a 19×9.5 ET35 sits 31 mm further out at the outer lip and 7 mm closer to the suspension at the inner barrel.
Which 2010–2016 Audi S4 wheel and tire upgrade keeps the speedometer most accurate?
Of the 2010–2016 Audi S4 upgrades listed here, 19×9.5 ET45 · 255/35R19 is closest to the stock 245/40R18, changing overall diameter by +1.2%. At an indicated 60 mph you would actually be doing 60.7 mph.
Do aftermarket wheels need hub-centric rings on a 2010–2016 Audi S4?
The 2010–2016 Audi S4's hub bore is 66.6 mm. Wheels machined to exactly 66.6 mm center on the hub directly; wheels with a larger bore need 66.6 mm hub-centric rings to avoid vibration.
Also on 5x112
These share the bolt pattern. Check offset, hub bore and brake clearance before swapping wheels.
| Vehicle | Generation | Bolt pattern | Hub bore |
|---|---|---|---|
| 2000–2002 Audi S4 | B5 | 5x112 | 57.1 mm |
| 2018–2025 Audi S4 | B9 | 5x112 | 66.5 mm |
| 2018–2022 Audi TT RS | 8S | 5x112 | 57.1 mm |
| 2020+ BMW 3 Series | G20 | 5x112 | 66.6 mm |
| 2023+ BMW M2 | G87 | 5x112 | 66.6 mm |
| 2021+ BMW M3 | G80 | 5x112 | 66.6 mm |