2021+ BMW M3 Wheel & Tire Fitment Guide

G80 generation, Base. 5x112 bolt pattern, stock 18×9.5 ET20 on 275/40R18. Compare 3 popular upgrades or try your own size.

Specs

Bolt pattern5x112
Center bore66.6 mm
Lug threadM14x1.25
Reference trimBase
Stock wheel18×9.5 ET20
Stock tire275/40R18
Stock overall diameter26.66 in

Calculator

Starts on the stock setup. Drag the sliders or load one of the popular upgrades below.

Wheel
in
in
mm
Tire
mm
%

The small mark on each slider shows the current value. Type in the box for sizes outside the slider range.

Custom vehicle measurementsOptional

Measure with your current wheels on the car and the results below show how much room the new setup leaves. The drawings use your numbers too. Leave blank anything you haven't measured.

  • Park on level ground at normal ride height, wheels straight.
  • Front and rear differ. Measure the axle you're changing, or enter the tighter corner.
ABCD

Millimetres or centimetres are recommended: small gaps are easier to read accurately than inch marks.

mm

Narrowest gap between the inside of the tire (or wheel, whichever sits further in) and the strut, spring perch or upper control arm. Wheels pointed straight.

mm

Hang a plumb line or hold a straightedge vertically from the fender lip above the hub, then measure across to the outermost point of the tire or wheel. Enter a negative number if it already sticks out.

mm

Straight up from the top of the tire to the fender lip, with the car on the ground at normal ride height.

mm

Smallest gap between the outer edge of the brake caliper and the inside of the wheel barrel.

Front section
StrutBrakeFender140.6Backspacing100.6Frontspacing
Three-quarter view
275/40R18
New setupCurrent setupFender and strut are drawn 12 mm outside and 28 mm inside your current setup. Add your own measurements for real clearance.
Poke
0mm
Wheel face stays where it is.
Inner clearance
0mm
Same room to the suspension.
Overall diameter
0%
0 in, within ±3%.
Speedo reads 60
60mph
Your actual speed.
VehicleBMW M3 Base
Bolt pattern5x112Hub bore66.6 mm
Current18×9.5 ET20, 275/40R18New18×9.5 ET20, 275/40R18

Notes

Questions

What bolt pattern does a 2021+ BMW M3 use?

The 2021+ BMW M3 uses a 5x112 bolt pattern with a 66.6 mm center bore and M14x1.25 lug threads.

What size wheels and tires are stock on the 2021+ BMW M3 Base?

The 2021+ BMW M3 Base came with 18×9.5 ET20 wheels and 275/40R18 tires, about 26.7 inches in overall diameter.

How far does a 18×10.5 ET18 wheel stick out on a 2021+ BMW M3?

On the 2021+ BMW M3, compared with the stock 18×9.5 ET20, a 18×10.5 ET18 sits 14.7 mm further out at the outer lip and 10.7 mm closer to the suspension at the inner barrel.

Which 2021+ BMW M3 wheel and tire upgrade keeps the speedometer most accurate?

Of the 2021+ BMW M3 upgrades listed here, 19×9.5 ET20 · 275/35R19 is closest to the stock 275/40R18, changing overall diameter by −0.3%. At an indicated 60 mph you would actually be doing 59.8 mph.

Do aftermarket wheels need hub-centric rings on a 2021+ BMW M3?

The 2021+ BMW M3's hub bore is 66.6 mm. Wheels machined to exactly 66.6 mm center on the hub directly; wheels with a larger bore need 66.6 mm hub-centric rings to avoid vibration.

Also on 5x112

These share the bolt pattern. Check offset, hub bore and brake clearance before swapping wheels.

VehicleGenerationBolt patternHub bore
2020+ BMW 3 SeriesG205x11266.6 mm
2023+ BMW M2G875x11266.6 mm
2020+ Toyota GR SupraA90/J295x11266.6 mm
2010–2016 Audi S4B8/B8.55x11266.6 mm
2000–2002 Audi S4B55x11257.1 mm
2018–2025 Audi S4B95x11266.5 mm