2009–2024 Nissan GT-R Wheel & Tire Fitment Guide

R35 generation, Premium. 5x114.3 bolt pattern, stock 20×9.5 ET45 on 255/40R20. Compare 2 popular upgrades or try your own size.

Specs

Bolt pattern5x114.3
Center bore66.1 mm
Lug threadM12x1.25
Reference trimPremium
Stock wheel20×9.5 ET45
Stock tire255/40R20
Stock overall diameter28.03 in

Calculator

Starts on the stock setup. Drag the sliders or load one of the popular upgrades below.

Wheel
in
in
mm
Tire
mm
%

The small mark on each slider shows the current value. Type in the box for sizes outside the slider range.

Custom vehicle measurementsOptional

Measure with your current wheels on the car and the results below show how much room the new setup leaves. The drawings use your numbers too. Leave blank anything you haven't measured.

  • Park on level ground at normal ride height, wheels straight.
  • Front and rear differ. Measure the axle you're changing, or enter the tighter corner.
ABCD

Millimetres or centimetres are recommended: small gaps are easier to read accurately than inch marks.

mm

Narrowest gap between the inside of the tire (or wheel, whichever sits further in) and the strut, spring perch or upper control arm. Wheels pointed straight.

mm

Hang a plumb line or hold a straightedge vertically from the fender lip above the hub, then measure across to the outermost point of the tire or wheel. Enter a negative number if it already sticks out.

mm

Straight up from the top of the tire to the fender lip, with the car on the ground at normal ride height.

mm

Smallest gap between the outer edge of the brake caliper and the inside of the wheel barrel.

Front section
StrutBrakeFender165.6Backspacing75.6 Frontspacing
Three-quarter view
255/40R20
New setupCurrent setupFender and strut are drawn 12 mm outside and 28 mm inside your current setup. Add your own measurements for real clearance.
Poke
0mm
Wheel face stays where it is.
Inner clearance
0mm
Same room to the suspension.
Overall diameter
0%
0 in, within ±3%.
Speedo reads 60
60mph
Your actual speed.
VehicleNissan GT-R Premium
Bolt pattern5x114.3Hub bore66.1 mm
Current20×9.5 ET45, 255/40R20New20×9.5 ET45, 255/40R20

Notes

Questions

What bolt pattern does a 2009–2024 Nissan GT-R use?

The 2009–2024 Nissan GT-R uses a 5x114.3 bolt pattern with a 66.1 mm center bore and M12x1.25 lug threads.

What size wheels and tires are stock on the 2009–2024 Nissan GT-R Premium?

The 2009–2024 Nissan GT-R Premium came with 20×9.5 ET45 wheels and 255/40R20 tires, about 28 inches in overall diameter.

How far does a 20×10 ET30 wheel stick out on a 2009–2024 Nissan GT-R?

On the 2009–2024 Nissan GT-R, compared with the stock 20×9.5 ET45, a 20×10 ET30 sits 21.4 mm further out at the outer lip and 8.6 mm further from the suspension at the inner barrel.

Which 2009–2024 Nissan GT-R wheel and tire upgrade keeps the speedometer most accurate?

Of the 2009–2024 Nissan GT-R upgrades listed here, 20×10 ET30 · 285/35R20 is closest to the stock 255/40R20, changing overall diameter by −0.6%. At an indicated 60 mph you would actually be doing 59.6 mph.

Do aftermarket wheels need hub-centric rings on a 2009–2024 Nissan GT-R?

The 2009–2024 Nissan GT-R's hub bore is 66.1 mm. Wheels machined to exactly 66.1 mm center on the hub directly; wheels with a larger bore need 66.1 mm hub-centric rings to avoid vibration.

Also on 5x114.3

These share the bolt pattern. Check offset, hub bore and brake clearance before swapping wheels.

VehicleGenerationBolt patternHub bore
2003–2008 Nissan 350ZZ335x114.366.1 mm
2009–2020 Nissan 370ZZ345x114.366.1 mm
2008–2013 Infiniti G37 CoupeV365x114.366.1 mm
2016–2024 Infiniti Q50V375x114.366.1 mm
2015–2021 Subaru WRXVA5x114.356.1 mm
2022+ Subaru WRXVB5x114.356.1 mm