2008–2013 Infiniti G37 Coupe Wheel & Tire Fitment Guide

V36 generation, Sport. 5x114.3 bolt pattern, stock 19×8.5 ET43 on 225/45R19. Compare 3 popular upgrades or try your own size.

Specs

Bolt pattern5x114.3
Center bore66.1 mm
Lug threadM12x1.25
Reference trimSport
Stock wheel19×8.5 ET43
Stock tire225/45R19
Stock overall diameter26.97 in

Calculator

Starts on the stock setup. Drag the sliders or load one of the popular upgrades below.

Wheel
in
in
mm
Tire
mm
%

The small mark on each slider shows the current value. Type in the box for sizes outside the slider range.

Custom vehicle measurementsOptional

Measure with your current wheels on the car and the results below show how much room the new setup leaves. The drawings use your numbers too. Leave blank anything you haven't measured.

  • Park on level ground at normal ride height, wheels straight.
  • Front and rear differ. Measure the axle you're changing, or enter the tighter corner.
ABCD

Millimetres or centimetres are recommended: small gaps are easier to read accurately than inch marks.

mm

Narrowest gap between the inside of the tire (or wheel, whichever sits further in) and the strut, spring perch or upper control arm. Wheels pointed straight.

mm

Hang a plumb line or hold a straightedge vertically from the fender lip above the hub, then measure across to the outermost point of the tire or wheel. Enter a negative number if it already sticks out.

mm

Straight up from the top of the tire to the fender lip, with the car on the ground at normal ride height.

mm

Smallest gap between the outer edge of the brake caliper and the inside of the wheel barrel.

Front section
StrutBrakeFender150.9Backspacing64.9 Frontspacing
Three-quarter view
225/45R19
New setupCurrent setupFender and strut are drawn 12 mm outside and 28 mm inside your current setup. Add your own measurements for real clearance.
Poke
0mm
Wheel face stays where it is.
Inner clearance
0mm
Same room to the suspension.
Overall diameter
0%
0 in, within ±3%.
Speedo reads 60
60mph
Your actual speed.
VehicleInfiniti G37 Coupe Sport
Bolt pattern5x114.3Hub bore66.1 mm
Current19×8.5 ET43, 225/45R19New19×8.5 ET43, 225/45R19

Notes

Questions

What bolt pattern does a 2008–2013 Infiniti G37 Coupe use?

The 2008–2013 Infiniti G37 Coupe uses a 5x114.3 bolt pattern with a 66.1 mm center bore and M12x1.25 lug threads.

What size wheels and tires are stock on the 2008–2013 Infiniti G37 Coupe Sport?

The 2008–2013 Infiniti G37 Coupe Sport came with 19×8.5 ET43 wheels and 225/45R19 tires, about 27 inches in overall diameter.

How far does a 19×9.5 ET22 wheel stick out on a 2008–2013 Infiniti G37 Coupe?

On the 2008–2013 Infiniti G37 Coupe, compared with the stock 19×8.5 ET43, a 19×9.5 ET22 sits 33.7 mm further out at the outer lip and 8.3 mm further from the suspension at the inner barrel.

Which 2008–2013 Infiniti G37 Coupe wheel and tire upgrade keeps the speedometer most accurate?

Of the 2008–2013 Infiniti G37 Coupe upgrades listed here, 19×9.5 ET30 · 255/40R19 is closest to the stock 225/45R19, changing overall diameter by +0.2%. At an indicated 60 mph you would actually be doing 60.1 mph.

Do aftermarket wheels need hub-centric rings on a 2008–2013 Infiniti G37 Coupe?

The 2008–2013 Infiniti G37 Coupe's hub bore is 66.1 mm. Wheels machined to exactly 66.1 mm center on the hub directly; wheels with a larger bore need 66.1 mm hub-centric rings to avoid vibration.

Also on 5x114.3

These share the bolt pattern. Check offset, hub bore and brake clearance before swapping wheels.

VehicleGenerationBolt patternHub bore
2016–2024 Infiniti Q50V375x114.366.1 mm
2003–2008 Nissan 350ZZ335x114.366.1 mm
2009–2020 Nissan 370ZZ345x114.366.1 mm
2009–2024 Nissan GT-RR355x114.366.1 mm
2015–2021 Subaru WRXVA5x114.356.1 mm
2022+ Subaru WRXVB5x114.356.1 mm