2023+ Toyota GR Corolla Wheel & Tire Fitment Guide
E210 generation, Core. 5x114.3 bolt pattern, stock 18×8.5 ET30 on 235/40R18. Compare 3 popular upgrades or try your own size.
Specs
| Bolt pattern | 5x114.3 |
|---|---|
| Center bore | 60.1 mm |
| Lug thread | M12x1.5 |
| Reference trim | Core |
| Stock wheel | 18×8.5 ET30 |
| Stock tire | 235/40R18 |
| Stock overall diameter | 25.4 in |
Calculator
Starts on the stock setup. Drag the sliders or load one of the popular upgrades below.
The small mark on each slider shows the current value. Type in the box for sizes outside the slider range.
Custom vehicle measurementsOptional
Measure with your current wheels on the car and the results below show how much room the new setup leaves. The drawings use your numbers too. Leave blank anything you haven't measured.
- Park on level ground at normal ride height, wheels straight.
- Front and rear differ. Measure the axle you're changing, or enter the tighter corner.
Millimetres or centimetres are recommended: small gaps are easier to read accurately than inch marks.
Narrowest gap between the inside of the tire (or wheel, whichever sits further in) and the strut, spring perch or upper control arm. Wheels pointed straight.
Hang a plumb line or hold a straightedge vertically from the fender lip above the hub, then measure across to the outermost point of the tire or wheel. Enter a negative number if it already sticks out.
Straight up from the top of the tire to the fender lip, with the car on the ground at normal ride height.
Smallest gap between the outer edge of the brake caliper and the inside of the wheel barrel.
- Poke
- 0mm
- Wheel face stays where it is.
- Inner clearance
- 0mm
- Same room to the suspension.
- Overall diameter
- 0%
- 0 in, within ±3%.
- Speedo reads 60
- 60mph
- Your actual speed.
| Vehicle | Toyota GR Corolla Core | ||
|---|---|---|---|
| Bolt pattern | 5x114.3 | Hub bore | 60.1 mm |
| Current | 18×8.5 ET30, 235/40R18 | New | 18×8.5 ET30, 235/40R18 |
Popular upgrades
Each size compared with the stock 18×8.5 ET30, 235/40R18.
| Setup | Poke | Inner clearance | Diameter | Speedo reads 60 | Action |
|---|---|---|---|---|---|
| Mild 18×818×8 ET35, 235/40R18 | −11.3 mm | +1.3 mm | 0% | 60 mph | |
| Flush 18×9.518×9.5 ET22, 265/35R18 | +20.7 mm | −4.7 mm | −0.4% | 59.8 mph | |
| Wide 18×1018×10 ET40, 265/35R18 | +9.1 mm | −29.1 mm | −0.4% | 59.8 mph |
Notes
- The rear wheels sit on factory 10 mm slip-on spacers, so the effective rear offset is about ET20 and aftermarket rear spacers usually replace the OE 10 mm piece.
- 18 inches is the practical minimum because of the 355 mm front rotors and fixed 4-piston calipers; spoke-to-caliper gap can get down to about 6 mm on some 18×8 wheels.
- The Morizo Edition uses 245/40R18 on the same 18×8.5 ET30 size.
- Aggressive 18×10 setups may need a 5 mm spacer to clear the front strut (not the caliper).
Questions
What bolt pattern does a 2023+ Toyota GR Corolla use?
The 2023+ Toyota GR Corolla uses a 5x114.3 bolt pattern with a 60.1 mm center bore and M12x1.5 lug threads.
What size wheels and tires are stock on the 2023+ Toyota GR Corolla Core?
The 2023+ Toyota GR Corolla Core came with 18×8.5 ET30 wheels and 235/40R18 tires, about 25.4 inches in overall diameter.
How far does a 18×9.5 ET22 wheel stick out on a 2023+ Toyota GR Corolla?
On the 2023+ Toyota GR Corolla, compared with the stock 18×8.5 ET30, a 18×9.5 ET22 sits 20.7 mm further out at the outer lip and 4.7 mm closer to the suspension at the inner barrel.
Which 2023+ Toyota GR Corolla wheel and tire upgrade keeps the speedometer most accurate?
Of the 2023+ Toyota GR Corolla upgrades listed here, 18×8 ET35 · 235/40R18 is closest to the stock 235/40R18, changing overall diameter by 0%. At an indicated 60 mph you would actually be doing 60 mph.
Do aftermarket wheels need hub-centric rings on a 2023+ Toyota GR Corolla?
The 2023+ Toyota GR Corolla's hub bore is 60.1 mm. Wheels machined to exactly 60.1 mm center on the hub directly; wheels with a larger bore need 60.1 mm hub-centric rings to avoid vibration.
Also on 5x114.3
These share the bolt pattern. Check offset, hub bore and brake clearance before swapping wheels.
| Vehicle | Generation | Bolt pattern | Hub bore |
|---|---|---|---|
| 1993–1998 Toyota Supra | A80 (MK4) | 5x114.3 | 60.1 mm |
| 2002–2006 Acura RSX | DC5 | 5x114.3 | 64.1 mm |
| 2009–2014 Acura TSX | CU2 | 5x114.3 | 64.1 mm |
| 2019+ Genesis G70 | 1st gen (IK) | 5x114.3 | 67.1 mm |
| 2016–2021 Honda Civic | 10th gen (FC/FK) | 5x114.3 | 64.1 mm |
| 2022+ Honda Civic | 11th gen (FE) | 5x114.3 | 64.1 mm |