2007–2018 Jeep Wrangler Wheel & Tire Fitment Guide
JK generation, Rubicon. 5x127 bolt pattern, stock 17×7.5 ET44.45 on 255/75R17. Compare 2 popular upgrades or try your own size.
Specs
| Bolt pattern | 5x127 |
|---|---|
| Center bore | 71.5 mm |
| Lug thread | 1/2-20 |
| Reference trim | Rubicon |
| Stock wheel | 17×7.5 ET44.45 |
| Stock tire | 255/75R17 |
| Stock overall diameter | 32.06 in |
Calculator
Starts on the stock setup. Drag the sliders or load one of the popular upgrades below.
The small mark on each slider shows the current value. Type in the box for sizes outside the slider range.
Custom vehicle measurementsOptional
Measure with your current wheels on the car and the results below show how much room the new setup leaves. The drawings use your numbers too. Leave blank anything you haven't measured.
- Park on level ground at normal ride height, wheels straight.
- Front and rear differ. Measure the axle you're changing, or enter the tighter corner.
Millimetres or centimetres are recommended: small gaps are easier to read accurately than inch marks.
Narrowest gap between the inside of the tire (or wheel, whichever sits further in) and the strut, spring perch or upper control arm. Wheels pointed straight.
Hang a plumb line or hold a straightedge vertically from the fender lip above the hub, then measure across to the outermost point of the tire or wheel. Enter a negative number if it already sticks out.
Straight up from the top of the tire to the fender lip, with the car on the ground at normal ride height.
Smallest gap between the outer edge of the brake caliper and the inside of the wheel barrel.
- Poke
- 0mm
- Wheel face stays where it is.
- Inner clearance
- 0mm
- Same room to the suspension.
- Overall diameter
- 0%
- 0 in, within ±3%.
- Speedo reads 60
- 60mph
- Your actual speed.
| Vehicle | Jeep Wrangler Rubicon | ||
|---|---|---|---|
| Bolt pattern | 5x127 | Hub bore | 71.5 mm |
| Current | 17×7.5 ET44.45, 255/75R17 | New | 17×7.5 ET44.45, 255/75R17 |
Popular upgrades
Each size compared with the stock 17×7.5 ET44.45, 255/75R17.
| Setup | Poke | Inner clearance | Diameter | Speedo reads 60 | Action |
|---|---|---|---|---|---|
| 33s, 17×8.5 4.5in BS17×8.5 ET-6, 285/70R17 | +63.1 mm | +37.8 mm | +2% | 61.2 mph | |
| 35s on 2.5in lift, 17×917×9 ET-12, 315/70R17 | +75.5 mm | +37.4 mm | +7.2% | 64.3 mph |
Notes
- Rubicon ships with LT255/75R17 (about 32 in) on 17×7.5 wheels with +44.45 mm offset (about 6.25 in backspacing).
- JK studs are SAE 1/2-20 with 19 mm lug nuts. JL and Gladiator wheels share the 5x127 pattern and 71.5 mm bore, but they use M14×1.5 nuts with a larger seat, so lug hardware does not swap between them.
- 33s (285/70R17) on wheels with about 4.5 in backspacing clear on the street with stock suspension, but they rub at full flex off-road.
- 35s (35x12.50R17, roughly 315/70R17) are normally run on a 2.5 in lift with 17×9 −12 wheels. Going past 2.5 in usually means dealing with the front driveshaft, or adding bump-stop extensions and trimming the fenders.
Questions
What bolt pattern does a 2007–2018 Jeep Wrangler use?
The 2007–2018 Jeep Wrangler uses a 5x127 bolt pattern with a 71.5 mm center bore and 1/2-20 lug threads.
What size wheels and tires are stock on the 2007–2018 Jeep Wrangler Rubicon?
The 2007–2018 Jeep Wrangler Rubicon came with 17×7.5 ET44.45 wheels and 255/75R17 tires, about 32.1 inches in overall diameter.
How far does a 17×9 ET-12 wheel stick out on a 2007–2018 Jeep Wrangler?
On the 2007–2018 Jeep Wrangler, compared with the stock 17×7.5 ET44.45, a 17×9 ET-12 sits 75.5 mm further out at the outer lip and 37.4 mm further from the suspension at the inner barrel.
Which 2007–2018 Jeep Wrangler wheel and tire upgrade keeps the speedometer most accurate?
Of the 2007–2018 Jeep Wrangler upgrades listed here, 17×8.5 ET-6 · 285/70R17 is closest to the stock 255/75R17, changing overall diameter by +2%. At an indicated 60 mph you would actually be doing 61.2 mph.
Do aftermarket wheels need hub-centric rings on a 2007–2018 Jeep Wrangler?
The 2007–2018 Jeep Wrangler's hub bore is 71.5 mm. Wheels machined to exactly 71.5 mm center on the hub directly; wheels with a larger bore need 71.5 mm hub-centric rings to avoid vibration.
Also on 5x127
These share the bolt pattern. Check offset, hub bore and brake clearance before swapping wheels.
| Vehicle | Generation | Bolt pattern | Hub bore |
|---|---|---|---|
| 2020+ Jeep Gladiator | JT | 5x127 | 71.5 mm |
| 2018+ Jeep Wrangler | JL | 5x127 | 71.5 mm |