2020+ Jeep Gladiator Wheel & Tire Fitment Guide
JT generation, Rubicon. 5x127 bolt pattern, stock 17×7.5 ET44.45 on 285/70R17. Compare 3 popular upgrades or try your own size.
Specs
| Bolt pattern | 5x127 |
|---|---|
| Center bore | 71.5 mm |
| Lug thread | M14x1.5 |
| Reference trim | Rubicon |
| Stock wheel | 17×7.5 ET44.45 |
| Stock tire | 285/70R17 |
| Stock overall diameter | 32.71 in |
Calculator
Starts on the stock setup. Drag the sliders or load one of the popular upgrades below.
The small mark on each slider shows the current value. Type in the box for sizes outside the slider range.
Custom vehicle measurementsOptional
Measure with your current wheels on the car and the results below show how much room the new setup leaves. The drawings use your numbers too. Leave blank anything you haven't measured.
- Park on level ground at normal ride height, wheels straight.
- Front and rear differ. Measure the axle you're changing, or enter the tighter corner.
Millimetres or centimetres are recommended: small gaps are easier to read accurately than inch marks.
Narrowest gap between the inside of the tire (or wheel, whichever sits further in) and the strut, spring perch or upper control arm. Wheels pointed straight.
Hang a plumb line or hold a straightedge vertically from the fender lip above the hub, then measure across to the outermost point of the tire or wheel. Enter a negative number if it already sticks out.
Straight up from the top of the tire to the fender lip, with the car on the ground at normal ride height.
Smallest gap between the outer edge of the brake caliper and the inside of the wheel barrel.
- Poke
- 0mm
- Wheel face stays where it is.
- Inner clearance
- 0mm
- Same room to the suspension.
- Overall diameter
- 0%
- 0 in, within ±3%.
- Speedo reads 60
- 60mph
- Your actual speed.
| Vehicle | Jeep Gladiator Rubicon | ||
|---|---|---|---|
| Bolt pattern | 5x127 | Hub bore | 71.5 mm |
| Current | 17×7.5 ET44.45, 285/70R17 | New | 17×7.5 ET44.45, 285/70R17 |
Popular upgrades
Each size compared with the stock 17×7.5 ET44.45, 285/70R17.
| Setup | Poke | Inner clearance | Diameter | Speedo reads 60 | Action |
|---|---|---|---|---|---|
| 35s on stock Rubicon wheels17×7.5 ET44.45, 315/70R17 | 0 mm | 0 mm | +5.1% | 63 mph | |
| 35s no lift, 17×9 +017×9 ET0, 315/70R17 | +63.5 mm | +25.4 mm | +5.1% | 63 mph | |
| 35s on lift, 17×9 −1217×9 ET-12, 315/70R17 | +75.5 mm | +37.4 mm | +5.1% | 63 mph |
Notes
- Rubicon ships with LT285/70R17 (about 33 in) on 17×7.5 wheels with +44.45 mm offset (6.25 in backspacing).
- Rubicon and Mojave have high-clearance fenders, so 35s (35x12.50R17, roughly 315/70R17) fit without a lift. They still rub at full articulation unless you add about 1 in bump-stop extensions and lightly trim the front pinch seam. Sport trims need a lift.
- The Xtreme Recon package comes with 315/70R17 tires on 17×8 beadlock-capable wheels.
- Lug nuts are M14×1.5 with a 22 mm hex. Wheels interchange with the JL Wrangler. JK wheels share the bolt pattern, but JK 1/2-20 lug nuts will not work.
Questions
What bolt pattern does a 2020+ Jeep Gladiator use?
The 2020+ Jeep Gladiator uses a 5x127 bolt pattern with a 71.5 mm center bore and M14x1.5 lug threads.
What size wheels and tires are stock on the 2020+ Jeep Gladiator Rubicon?
The 2020+ Jeep Gladiator Rubicon came with 17×7.5 ET44.45 wheels and 285/70R17 tires, about 32.7 inches in overall diameter.
How far does a 17×9 ET-12 wheel stick out on a 2020+ Jeep Gladiator?
On the 2020+ Jeep Gladiator, compared with the stock 17×7.5 ET44.45, a 17×9 ET-12 sits 75.5 mm further out at the outer lip and 37.4 mm further from the suspension at the inner barrel.
Which 2020+ Jeep Gladiator wheel and tire upgrade keeps the speedometer most accurate?
Of the 2020+ Jeep Gladiator upgrades listed here, 17×7.5 ET44.45 · 315/70R17 is closest to the stock 285/70R17, changing overall diameter by +5.1%. At an indicated 60 mph you would actually be doing 63 mph.
Do aftermarket wheels need hub-centric rings on a 2020+ Jeep Gladiator?
The 2020+ Jeep Gladiator's hub bore is 71.5 mm. Wheels machined to exactly 71.5 mm center on the hub directly; wheels with a larger bore need 71.5 mm hub-centric rings to avoid vibration.
Also on 5x127
These share the bolt pattern. Check offset, hub bore and brake clearance before swapping wheels.
| Vehicle | Generation | Bolt pattern | Hub bore |
|---|---|---|---|
| 2018+ Jeep Wrangler | JL | 5x127 | 71.5 mm |
| 2007–2018 Jeep Wrangler | JK | 5x127 | 71.5 mm |