2000–2009 Honda S2000 Wheel & Tire Fitment Guide

AP1/AP2 generation, Base (AP2 17-inch). 5x114.3 bolt pattern, stock 17×7 ET55 on 215/45R17. Compare 2 popular upgrades or try your own size.

Specs

Bolt pattern5x114.3
Center bore70.1 mm
Lug threadM12x1.5
Reference trimBase (AP2 17-inch)
Stock wheel17×7 ET55
Stock tire215/45R17
Stock overall diameter24.62 in

Calculator

Starts on the stock setup. Drag the sliders or load one of the popular upgrades below.

Wheel
in
in
mm
Tire
mm
%

The small mark on each slider shows the current value. Type in the box for sizes outside the slider range.

Custom vehicle measurementsOptional

Measure with your current wheels on the car and the results below show how much room the new setup leaves. The drawings use your numbers too. Leave blank anything you haven't measured.

  • Park on level ground at normal ride height, wheels straight.
  • Front and rear differ. Measure the axle you're changing, or enter the tighter corner.
ABCD

Millimetres or centimetres are recommended: small gaps are easier to read accurately than inch marks.

mm

Narrowest gap between the inside of the tire (or wheel, whichever sits further in) and the strut, spring perch or upper control arm. Wheels pointed straight.

mm

Hang a plumb line or hold a straightedge vertically from the fender lip above the hub, then measure across to the outermost point of the tire or wheel. Enter a negative number if it already sticks out.

mm

Straight up from the top of the tire to the fender lip, with the car on the ground at normal ride height.

mm

Smallest gap between the outer edge of the brake caliper and the inside of the wheel barrel.

Front section
StrutBrakeFender143.9Backspacing33.9 Frontspacing
Three-quarter view
215/45R17
New setupCurrent setupFender and strut are drawn 12 mm outside and 28 mm inside your current setup. Add your own measurements for real clearance.
Poke
0mm
Wheel face stays where it is.
Inner clearance
0mm
Same room to the suspension.
Overall diameter
0%
0 in, within ±3%.
Speedo reads 60
60mph
Your actual speed.
VehicleHonda S2000 Base (AP2 17-inch)
Bolt pattern5x114.3Hub bore70.1 mm
Current17×7 ET55, 215/45R17New17×7 ET55, 215/45R17

Notes

Questions

What bolt pattern does a 2000–2009 Honda S2000 use?

The 2000–2009 Honda S2000 uses a 5x114.3 bolt pattern with a 70.1 mm center bore and M12x1.5 lug threads.

What size wheels and tires are stock on the 2000–2009 Honda S2000 Base (AP2 17-inch)?

The 2000–2009 Honda S2000 Base (AP2 17-inch) came with 17×7 ET55 wheels and 215/45R17 tires, about 24.6 inches in overall diameter.

How far does a 17×9 ET45 wheel stick out on a 2000–2009 Honda S2000?

On the 2000–2009 Honda S2000, compared with the stock 17×7 ET55, a 17×9 ET45 sits 35.4 mm further out at the outer lip and 15.4 mm closer to the suspension at the inner barrel.

Which 2000–2009 Honda S2000 wheel and tire upgrade keeps the speedometer most accurate?

Of the 2000–2009 Honda S2000 upgrades listed here, 17×8 ET50 · 225/45R17 is closest to the stock 215/45R17, changing overall diameter by +1.4%. At an indicated 60 mph you would actually be doing 60.9 mph.

Do aftermarket wheels need hub-centric rings on a 2000–2009 Honda S2000?

The 2000–2009 Honda S2000's hub bore is 70.1 mm. Wheels machined to exactly 70.1 mm center on the hub directly; wheels with a larger bore need 70.1 mm hub-centric rings to avoid vibration.

Also on 5x114.3

These share the bolt pattern. Check offset, hub bore and brake clearance before swapping wheels.

VehicleGenerationBolt patternHub bore
2016–2021 Honda Civic10th gen (FC/FK)5x114.364.1 mm
2022+ Honda Civic11th gen (FE)5x114.364.1 mm
2002–2006 Acura RSXDC55x114.364.1 mm
2009–2014 Acura TSXCU25x114.364.1 mm
2019+ Genesis G701st gen (IK)5x114.367.1 mm
2018–2023 Kia StingerCK5x114.367.1 mm