2024+ Ford Ranger Raptor Wheel & Tire Fitment Guide
P703 generation, Raptor. 6x139.7 bolt pattern, stock 17×8.5 ET55 on 285/70R17. Compare 3 popular upgrades or try your own size.
Specs
| Bolt pattern | 6x139.7 |
|---|---|
| Center bore | 93.1 mm |
| Lug thread | M12x1.5 |
| Reference trim | Raptor |
| Stock wheel | 17×8.5 ET55 |
| Stock tire | 285/70R17 |
| Stock overall diameter | 32.71 in |
Calculator
Starts on the stock setup. Drag the sliders or load one of the popular upgrades below.
The small mark on each slider shows the current value. Type in the box for sizes outside the slider range.
Custom vehicle measurementsOptional
Measure with your current wheels on the car and the results below show how much room the new setup leaves. The drawings use your numbers too. Leave blank anything you haven't measured.
- Park on level ground at normal ride height, wheels straight.
- Front and rear differ. Measure the axle you're changing, or enter the tighter corner.
Millimetres or centimetres are recommended: small gaps are easier to read accurately than inch marks.
Narrowest gap between the inside of the tire (or wheel, whichever sits further in) and the strut, spring perch or upper control arm. Wheels pointed straight.
Hang a plumb line or hold a straightedge vertically from the fender lip above the hub, then measure across to the outermost point of the tire or wheel. Enter a negative number if it already sticks out.
Straight up from the top of the tire to the fender lip, with the car on the ground at normal ride height.
Smallest gap between the outer edge of the brake caliper and the inside of the wheel barrel.
- Poke
- 0mm
- Wheel face stays where it is.
- Inner clearance
- 0mm
- Same room to the suspension.
- Overall diameter
- 0%
- 0 in, within ±3%.
- Speedo reads 60
- 60mph
- Your actual speed.
| Vehicle | Ford Ranger Raptor Raptor | ||
|---|---|---|---|
| Bolt pattern | 6x139.7 | Hub bore | 93.1 mm |
| Current | 17×8.5 ET55, 285/70R17 | New | 17×8.5 ET55, 285/70R17 |
Popular upgrades
Each size compared with the stock 17×8.5 ET55, 285/70R17.
| Setup | Poke | Inner clearance | Diameter | Speedo reads 60 | Action |
|---|---|---|---|---|---|
| Flush 17×8 ET3017×8 ET30, 285/70R17 | +18.7 mm | +31.3 mm | 0% | 60 mph | |
| 34in 17×9 ET2517×9 ET25, 285/75R17 | +36.4 mm | +23.6 mm | +3.4% | 62.1 mph | |
| 35in 17×9 ET1817×9 ET18, 315/70R17 | +43.4 mm | +30.6 mm | +5.1% | 63 mph |
Notes
- Stock tire is an LT285/70R17 BFGoodrich KO3 (about 32.8 in tall) on 17×8.5 ET55 beadlock-capable wheels.
- Lower-offset wheels and bigger tires mainly rub the front crash bars at full lock, worst in reverse, and the inner fender liners under compression.
- 34-35 in tires (285/75R17, 315/70R17 or 35x12.50R17) usually need the crash bars cut or replaced, and often a 2 in front level.
- Lug nuts are M12x1.5 on a 93.1 mm hub, the same bolt pattern and bore as other 2019+ Rangers.
Questions
What bolt pattern does a 2024+ Ford Ranger Raptor use?
The 2024+ Ford Ranger Raptor uses a 6x139.7 bolt pattern with a 93.1 mm center bore and M12x1.5 lug threads.
What size wheels and tires are stock on the 2024+ Ford Ranger Raptor Raptor?
The 2024+ Ford Ranger Raptor Raptor came with 17×8.5 ET55 wheels and 285/70R17 tires, about 32.7 inches in overall diameter.
How far does a 17×9 ET18 wheel stick out on a 2024+ Ford Ranger Raptor?
On the 2024+ Ford Ranger Raptor, compared with the stock 17×8.5 ET55, a 17×9 ET18 sits 43.4 mm further out at the outer lip and 30.6 mm further from the suspension at the inner barrel.
Which 2024+ Ford Ranger Raptor wheel and tire upgrade keeps the speedometer most accurate?
Of the 2024+ Ford Ranger Raptor upgrades listed here, 17×8 ET30 · 285/70R17 is closest to the stock 285/70R17, changing overall diameter by 0%. At an indicated 60 mph you would actually be doing 60 mph.
Do aftermarket wheels need hub-centric rings on a 2024+ Ford Ranger Raptor?
The 2024+ Ford Ranger Raptor's hub bore is 93.1 mm. Wheels machined to exactly 93.1 mm center on the hub directly; wheels with a larger bore need 93.1 mm hub-centric rings to avoid vibration.
Also on 6x139.7
These share the bolt pattern. Check offset, hub bore and brake clearance before swapping wheels.
| Vehicle | Generation | Bolt pattern | Hub bore |
|---|---|---|---|
| 2021+ Ford Bronco | 6th gen (U725) | 6x139.7 | 93.1 mm |
| 2016–2023 Toyota Tacoma | 3rd gen | 6x139.7 | 106.1 mm |