2015–2020 Ford Mustang Shelby GT350 Wheel & Tire Fitment Guide
S550 generation, Base. 5x114.3 bolt pattern, stock 19×10.5 ET30 on 295/35R19. Compare 2 popular upgrades or try your own size.
Specs
| Bolt pattern | 5x114.3 |
|---|---|
| Center bore | 70.5 mm |
| Lug thread | M14x1.5 |
| Reference trim | Base |
| Stock wheel | 19×10.5 ET30 |
| Stock tire | 295/35R19 |
| Stock overall diameter | 27.13 in |
Calculator
Starts on the stock setup. Drag the sliders or load one of the popular upgrades below.
The small mark on each slider shows the current value. Type in the box for sizes outside the slider range.
Custom vehicle measurementsOptional
Measure with your current wheels on the car and the results below show how much room the new setup leaves. The drawings use your numbers too. Leave blank anything you haven't measured.
- Park on level ground at normal ride height, wheels straight.
- Front and rear differ. Measure the axle you're changing, or enter the tighter corner.
Millimetres or centimetres are recommended: small gaps are easier to read accurately than inch marks.
Narrowest gap between the inside of the tire (or wheel, whichever sits further in) and the strut, spring perch or upper control arm. Wheels pointed straight.
Hang a plumb line or hold a straightedge vertically from the fender lip above the hub, then measure across to the outermost point of the tire or wheel. Enter a negative number if it already sticks out.
Straight up from the top of the tire to the fender lip, with the car on the ground at normal ride height.
Smallest gap between the outer edge of the brake caliper and the inside of the wheel barrel.
- Poke
- 0mm
- Wheel face stays where it is.
- Inner clearance
- 0mm
- Same room to the suspension.
- Overall diameter
- 0%
- 0 in, within ±3%.
- Speedo reads 60
- 60mph
- Your actual speed.
| Vehicle | Ford Mustang Shelby GT350 Base | ||
|---|---|---|---|
| Bolt pattern | 5x114.3 | Hub bore | 70.5 mm |
| Current | 19×10.5 ET30, 295/35R19 | New | 19×10.5 ET30, 295/35R19 |
Popular upgrades
Each size compared with the stock 19×10.5 ET30, 295/35R19.
| Setup | Poke | Inner clearance | Diameter | Speedo reads 60 | Action |
|---|---|---|---|---|---|
| Square 19×11 + spacer19×11 ET27, 305/30R19 | +9.3 mm | −3.3 mm | −3.4% | 58 mph | |
| Track 18×11 + spacer18×11 ET27, 305/35R18 | +9.3 mm | −3.3 mm | −2.7% | 58.4 mph |
Notes
- Rear stock: 19×11 ET62 with 305/35R19. The GT350R instead runs carbon 19×11 front and 19×11.5 ET56 rear wheels on 305/30R19 and 315/30R19.
- The common square setup is 19×11 ET52 at all four corners with a 25 mm front spacer and extended studs (about ET27 effective up front). The OEM ET62 rear may hit the front strut if moved to the front.
- The GT350's large front Brembo brakes limit 18-inch wheels to designs that clear them; Apex runs 18×11 ET52 EC-7s with 305/35R18 and a 25–30 mm front spacer.
- Uses M14x1.5 lug nuts on a 5x114.3 / 70.5 mm hub, the same as other 2015+ Mustangs.
Questions
What bolt pattern does a 2015–2020 Ford Mustang Shelby GT350 use?
The 2015–2020 Ford Mustang Shelby GT350 uses a 5x114.3 bolt pattern with a 70.5 mm center bore and M14x1.5 lug threads.
What size wheels and tires are stock on the 2015–2020 Ford Mustang Shelby GT350 Base?
The 2015–2020 Ford Mustang Shelby GT350 Base came with 19×10.5 ET30 wheels and 295/35R19 tires, about 27.1 inches in overall diameter.
How far does a 19×11 ET27 wheel stick out on a 2015–2020 Ford Mustang Shelby GT350?
On the 2015–2020 Ford Mustang Shelby GT350, compared with the stock 19×10.5 ET30, a 19×11 ET27 sits 9.3 mm further out at the outer lip and 3.3 mm closer to the suspension at the inner barrel.
Which 2015–2020 Ford Mustang Shelby GT350 wheel and tire upgrade keeps the speedometer most accurate?
Of the 2015–2020 Ford Mustang Shelby GT350 upgrades listed here, 18×11 ET27 · 305/35R18 is closest to the stock 295/35R19, changing overall diameter by −2.7%. At an indicated 60 mph you would actually be doing 58.4 mph.
Do aftermarket wheels need hub-centric rings on a 2015–2020 Ford Mustang Shelby GT350?
The 2015–2020 Ford Mustang Shelby GT350's hub bore is 70.5 mm. Wheels machined to exactly 70.5 mm center on the hub directly; wheels with a larger bore need 70.5 mm hub-centric rings to avoid vibration.
Also on 5x114.3
These share the bolt pattern. Check offset, hub bore and brake clearance before swapping wheels.
| Vehicle | Generation | Bolt pattern | Hub bore |
|---|---|---|---|
| 2015–2017 Ford Mustang | S550 | 5x114.3 | 70.5 mm |
| 2025+ Hyundai Ioniq 5 N | NE | 5x114.3 | 67.1 mm |
| 2017–2023 Tesla Model 3 | Gen 1 | 5x114.3 | 64.1 mm |
| 2002–2006 Acura RSX | DC5 | 5x114.3 | 64.1 mm |
| 2009–2014 Acura TSX | CU2 | 5x114.3 | 64.1 mm |
| 2019+ Genesis G70 | 1st gen (IK) | 5x114.3 | 67.1 mm |