2013–2016 BMW M5 Wheel & Tire Fitment Guide

F10 generation, Base. 5x120 bolt pattern, stock 19×9 ET32 on 265/40R19. Compare 2 popular upgrades or try your own size.

Specs

Bolt pattern5x120
Center bore72.6 mm
Lug threadM14x1.25
Reference trimBase
Stock wheel19×9 ET32
Stock tire265/40R19
Stock overall diameter27.35 in

Calculator

Starts on the stock setup. Drag the sliders or load one of the popular upgrades below.

Wheel
in
in
mm
Tire
mm
%

The small mark on each slider shows the current value. Type in the box for sizes outside the slider range.

Custom vehicle measurementsOptional

Measure with your current wheels on the car and the results below show how much room the new setup leaves. The drawings use your numbers too. Leave blank anything you haven't measured.

  • Park on level ground at normal ride height, wheels straight.
  • Front and rear differ. Measure the axle you're changing, or enter the tighter corner.
ABCD

Millimetres or centimetres are recommended: small gaps are easier to read accurately than inch marks.

mm

Narrowest gap between the inside of the tire (or wheel, whichever sits further in) and the strut, spring perch or upper control arm. Wheels pointed straight.

mm

Hang a plumb line or hold a straightedge vertically from the fender lip above the hub, then measure across to the outermost point of the tire or wheel. Enter a negative number if it already sticks out.

mm

Straight up from the top of the tire to the fender lip, with the car on the ground at normal ride height.

mm

Smallest gap between the outer edge of the brake caliper and the inside of the wheel barrel.

Front section
StrutBrakeFender146.3Backspacing82.3 Frontspacing
Three-quarter view
265/40R19
New setupCurrent setupFender and strut are drawn 12 mm outside and 28 mm inside your current setup. Add your own measurements for real clearance.
Poke
0mm
Wheel face stays where it is.
Inner clearance
0mm
Same room to the suspension.
Overall diameter
0%
0 in, within ±3%.
Speedo reads 60
60mph
Your actual speed.
VehicleBMW M5 Base
Bolt pattern5x120Hub bore72.6 mm
Current19×9 ET32, 265/40R19New19×9 ET32, 265/40R19

Notes

Questions

What bolt pattern does a 2013–2016 BMW M5 use?

The 2013–2016 BMW M5 uses a 5x120 bolt pattern with a 72.6 mm center bore and M14x1.25 lug threads.

What size wheels and tires are stock on the 2013–2016 BMW M5 Base?

The 2013–2016 BMW M5 Base came with 19×9 ET32 wheels and 265/40R19 tires, about 27.3 inches in overall diameter.

How far does a 19×9.5 ET22 wheel stick out on a 2013–2016 BMW M5?

On the 2013–2016 BMW M5, compared with the stock 19×9 ET32, a 19×9.5 ET22 sits 16.3 mm further out at the outer lip and 3.7 mm further from the suspension at the inner barrel.

Which 2013–2016 BMW M5 wheel and tire upgrade keeps the speedometer most accurate?

Of the 2013–2016 BMW M5 upgrades listed here, 19×9.5 ET22 · 265/40R19 is closest to the stock 265/40R19, changing overall diameter by 0%. At an indicated 60 mph you would actually be doing 60 mph.

Do aftermarket wheels need hub-centric rings on a 2013–2016 BMW M5?

The 2013–2016 BMW M5's hub bore is 72.6 mm. Wheels machined to exactly 72.6 mm center on the hub directly; wheels with a larger bore need 72.6 mm hub-centric rings to avoid vibration.

Also on 5x120

These share the bolt pattern. Check offset, hub bore and brake clearance before swapping wheels.

VehicleGenerationBolt patternHub bore
2016–2021 BMW M2F875x12072.6 mm
2015–2018 BMW M3F805x12072.6 mm
1992–1999 BMW 3 SeriesE365x12072.6 mm
1999–2006 BMW 3 SeriesE465x12072.6 mm
2001–2006 BMW M3E465x12072.6 mm
2008–2013 BMW M3E90/E925x12072.6 mm