2022+ Toyota GR86 Wheel & Tire Fitment Guide
ZN8 generation, Premium. 5x100 bolt pattern, stock 18×7.5 ET48 on 215/40R18. Compare 3 popular upgrades or try your own size.
Specs
| Bolt pattern | 5x100 |
|---|---|
| Center bore | 56.1 mm |
| Lug thread | M12x1.25 |
| Reference trim | Premium |
| Stock wheel | 18×7.5 ET48 |
| Stock tire | 215/40R18 |
| Stock overall diameter | 24.77 in |
Calculator
Starts on the stock setup. Drag the sliders or load one of the popular upgrades below.
The small mark on each slider shows the current value. Type in the box for sizes outside the slider range.
Custom vehicle measurementsOptional
Measure with your current wheels on the car and the results below show how much room the new setup leaves. The drawings use your numbers too. Leave blank anything you haven't measured.
- Park on level ground at normal ride height, wheels straight.
- Front and rear differ. Measure the axle you're changing, or enter the tighter corner.
Millimetres or centimetres are recommended: small gaps are easier to read accurately than inch marks.
Narrowest gap between the inside of the tire (or wheel, whichever sits further in) and the strut, spring perch or upper control arm. Wheels pointed straight.
Hang a plumb line or hold a straightedge vertically from the fender lip above the hub, then measure across to the outermost point of the tire or wheel. Enter a negative number if it already sticks out.
Straight up from the top of the tire to the fender lip, with the car on the ground at normal ride height.
Smallest gap between the outer edge of the brake caliper and the inside of the wheel barrel.
- Poke
- 0mm
- Wheel face stays where it is.
- Inner clearance
- 0mm
- Same room to the suspension.
- Overall diameter
- 0%
- 0 in, within ±3%.
- Speedo reads 60
- 60mph
- Your actual speed.
| Vehicle | Toyota GR86 Premium | ||
|---|---|---|---|
| Bolt pattern | 5x100 | Hub bore | 56.1 mm |
| Current | 18×7.5 ET48, 215/40R18 | New | 18×7.5 ET48, 215/40R18 |
Popular upgrades
Each size compared with the stock 18×7.5 ET48, 215/40R18.
| Setup | Poke | Inner clearance | Diameter | Speedo reads 60 | Action |
|---|---|---|---|---|---|
| Daily 18×8.518×8.5 ET40, 235/40R18 | +20.7 mm | −4.7 mm | +2.5% | 61.5 mph | |
| 17×9 track setup17×9 ET38, 245/40R17 | +29 mm | −9.1 mm | −0.2% | 59.9 mph | |
| Wide 18×9.518×9.5 ET35, 255/35R18 | +38.4 mm | −12.4 mm | +1% | 60.6 mph |
Notes
- Base models come on 17×7.5 ET48 wheels with 215/45R17 tires; the 10th Anniversary edition used 18×8 ET40.
- Shares 5x100, a 56.1 mm hub bore and M12x1.25 studs with the Subaru BRZ and the first-generation 86/FR-S/BRZ, so wheels swap across all of them.
- On the stock struts the front spring perch limits wheels to about 9 inches wide; 18×9.5 setups need coilovers and roughly −2° to −2.5° camber.
- With 255-wide tires below about ET40, trim the rear bumper tab or it will groove the sidewall.
Questions
What bolt pattern does a 2022+ Toyota GR86 use?
The 2022+ Toyota GR86 uses a 5x100 bolt pattern with a 56.1 mm center bore and M12x1.25 lug threads.
What size wheels and tires are stock on the 2022+ Toyota GR86 Premium?
The 2022+ Toyota GR86 Premium came with 18×7.5 ET48 wheels and 215/40R18 tires, about 24.8 inches in overall diameter.
How far does a 18×9.5 ET35 wheel stick out on a 2022+ Toyota GR86?
On the 2022+ Toyota GR86, compared with the stock 18×7.5 ET48, a 18×9.5 ET35 sits 38.4 mm further out at the outer lip and 12.4 mm closer to the suspension at the inner barrel.
Which 2022+ Toyota GR86 wheel and tire upgrade keeps the speedometer most accurate?
Of the 2022+ Toyota GR86 upgrades listed here, 17×9 ET38 · 245/40R17 is closest to the stock 215/40R18, changing overall diameter by −0.2%. At an indicated 60 mph you would actually be doing 59.9 mph.
Do aftermarket wheels need hub-centric rings on a 2022+ Toyota GR86?
The 2022+ Toyota GR86's hub bore is 56.1 mm. Wheels machined to exactly 56.1 mm center on the hub directly; wheels with a larger bore need 56.1 mm hub-centric rings to avoid vibration.
Also on 5x100
These share the bolt pattern. Check offset, hub bore and brake clearance before swapping wheels.
| Vehicle | Generation | Bolt pattern | Hub bore |
|---|---|---|---|
| 2013–2020 Subaru BRZ | ZC6 | 5x100 | 56.1 mm |
| 2022+ Subaru BRZ | ZD8 | 5x100 | 56.1 mm |