1990–1997 Mazda MX-5 Miata Wheel & Tire Fitment Guide

NA generation, Base. 4x100 bolt pattern, stock 14×5.5 ET45 on 185/60R14. Compare 2 popular upgrades or try your own size.

Specs

Bolt pattern4x100
Center bore54.1 mm
Lug threadM12x1.5
Reference trimBase
Stock wheel14×5.5 ET45
Stock tire185/60R14
Stock overall diameter22.74 in

Calculator

Starts on the stock setup. Drag the sliders or load one of the popular upgrades below.

Wheel
in
in
mm
Tire
mm
%

The small mark on each slider shows the current value. Type in the box for sizes outside the slider range.

Custom vehicle measurementsOptional

Measure with your current wheels on the car and the results below show how much room the new setup leaves. The drawings use your numbers too. Leave blank anything you haven't measured.

  • Park on level ground at normal ride height, wheels straight.
  • Front and rear differ. Measure the axle you're changing, or enter the tighter corner.
ABCD

Millimetres or centimetres are recommended: small gaps are easier to read accurately than inch marks.

mm

Narrowest gap between the inside of the tire (or wheel, whichever sits further in) and the strut, spring perch or upper control arm. Wheels pointed straight.

mm

Hang a plumb line or hold a straightedge vertically from the fender lip above the hub, then measure across to the outermost point of the tire or wheel. Enter a negative number if it already sticks out.

mm

Straight up from the top of the tire to the fender lip, with the car on the ground at normal ride height.

mm

Smallest gap between the outer edge of the brake caliper and the inside of the wheel barrel.

Front section
StrutBrakeFender114.8Backspacing24.8 Frontspacing
Three-quarter view
185/60R14
New setupCurrent setupFender and strut are drawn 12 mm outside and 28 mm inside your current setup. Add your own measurements for real clearance.
Poke
0mm
Wheel face stays where it is.
Inner clearance
0mm
Same room to the suspension.
Overall diameter
0%
0 in, within ±3%.
Speedo reads 60
60mph
Your actual speed.
VehicleMazda MX-5 Miata Base
Bolt pattern4x100Hub bore54.1 mm
Current14×5.5 ET45, 185/60R14New14×5.5 ET45, 185/60R14

Notes

Questions

What bolt pattern does a 1990–1997 Mazda MX-5 Miata use?

The 1990–1997 Mazda MX-5 Miata uses a 4x100 bolt pattern with a 54.1 mm center bore and M12x1.5 lug threads.

What size wheels and tires are stock on the 1990–1997 Mazda MX-5 Miata Base?

The 1990–1997 Mazda MX-5 Miata Base came with 14×5.5 ET45 wheels and 185/60R14 tires, about 22.7 inches in overall diameter.

How far does a 15×9 ET36 wheel stick out on a 1990–1997 Mazda MX-5 Miata?

On the 1990–1997 Mazda MX-5 Miata, compared with the stock 14×5.5 ET45, a 15×9 ET36 sits 53.5 mm further out at the outer lip and 35.5 mm closer to the suspension at the inner barrel.

Which 1990–1997 Mazda MX-5 Miata wheel and tire upgrade keeps the speedometer most accurate?

Of the 1990–1997 Mazda MX-5 Miata upgrades listed here, 15×9 ET36 · 225/45R15 is closest to the stock 185/60R14, changing overall diameter by +1%. At an indicated 60 mph you would actually be doing 60.6 mph.

Do aftermarket wheels need hub-centric rings on a 1990–1997 Mazda MX-5 Miata?

The 1990–1997 Mazda MX-5 Miata's hub bore is 54.1 mm. Wheels machined to exactly 54.1 mm center on the hub directly; wheels with a larger bore need 54.1 mm hub-centric rings to avoid vibration.

Also on 4x100

These share the bolt pattern. Check offset, hub bore and brake clearance before swapping wheels.

VehicleGenerationBolt patternHub bore
2016+ Mazda MX-5 MiataND4x10054.1 mm