2016–2018 Ford Focus RS Wheel & Tire Fitment Guide
Mk3 generation, RS. 5x108 bolt pattern, stock 19×8 ET50 on 235/35R19. Compare 2 popular upgrades or try your own size.
Specs
| Bolt pattern | 5x108 |
|---|---|
| Center bore | 63.4 mm |
| Lug thread | M12x1.5 |
| Reference trim | RS |
| Stock wheel | 19×8 ET50 |
| Stock tire | 235/35R19 |
| Stock overall diameter | 25.48 in |
Calculator
Starts on the stock setup. Drag the sliders or load one of the popular upgrades below.
The small mark on each slider shows the current value. Type in the box for sizes outside the slider range.
Custom vehicle measurementsOptional
Measure with your current wheels on the car and the results below show how much room the new setup leaves. The drawings use your numbers too. Leave blank anything you haven't measured.
- Park on level ground at normal ride height, wheels straight.
- Front and rear differ. Measure the axle you're changing, or enter the tighter corner.
Millimetres or centimetres are recommended: small gaps are easier to read accurately than inch marks.
Narrowest gap between the inside of the tire (or wheel, whichever sits further in) and the strut, spring perch or upper control arm. Wheels pointed straight.
Hang a plumb line or hold a straightedge vertically from the fender lip above the hub, then measure across to the outermost point of the tire or wheel. Enter a negative number if it already sticks out.
Straight up from the top of the tire to the fender lip, with the car on the ground at normal ride height.
Smallest gap between the outer edge of the brake caliper and the inside of the wheel barrel.
- Poke
- 0mm
- Wheel face stays where it is.
- Inner clearance
- 0mm
- Same room to the suspension.
- Overall diameter
- 0%
- 0 in, within ±3%.
- Speedo reads 60
- 60mph
- Your actual speed.
| Vehicle | Ford Focus RS RS | ||
|---|---|---|---|
| Bolt pattern | 5x108 | Hub bore | 63.4 mm |
| Current | 19×8 ET50, 235/35R19 | New | 19×8 ET50, 235/35R19 |
Popular upgrades
Each size compared with the stock 19×8 ET50, 235/35R19.
| Setup | Poke | Inner clearance | Diameter | Speedo reads 60 | Action |
|---|---|---|---|---|---|
| Flush 19×8.519×8.5 ET40, 235/35R19 | +16.3 mm | +3.7 mm | 0% | 60 mph | |
| Track 18×9.518×9.5 ET40, 265/35R18 | +29 mm | −9 mm | −0.7% | 59.6 mph |
Notes
- The RS's 4-piston Brembo front calipers rule out most 17-inch wheels. 18s need to be checked for caliper clearance, and high-disk designs give the most room.
- The hub bore is 63.4 mm, so aftermarket wheels with 72.6 or 73.1 mm bores need hub-centric rings. The car uses M12x1.5 lug nuts.
- An 18×9.5 ET40 wheel with 265/35R18 tires is a common track size, but owners report minor rubbing under hard driving. About ET40 on an 8.5-inch wheel is the usual flush street fitment.
Questions
What bolt pattern does a 2016–2018 Ford Focus RS use?
The 2016–2018 Ford Focus RS uses a 5x108 bolt pattern with a 63.4 mm center bore and M12x1.5 lug threads.
What size wheels and tires are stock on the 2016–2018 Ford Focus RS RS?
The 2016–2018 Ford Focus RS RS came with 19×8 ET50 wheels and 235/35R19 tires, about 25.5 inches in overall diameter.
How far does a 18×9.5 ET40 wheel stick out on a 2016–2018 Ford Focus RS?
On the 2016–2018 Ford Focus RS, compared with the stock 19×8 ET50, a 18×9.5 ET40 sits 29 mm further out at the outer lip and 9 mm closer to the suspension at the inner barrel.
Which 2016–2018 Ford Focus RS wheel and tire upgrade keeps the speedometer most accurate?
Of the 2016–2018 Ford Focus RS upgrades listed here, 19×8.5 ET40 · 235/35R19 is closest to the stock 235/35R19, changing overall diameter by 0%. At an indicated 60 mph you would actually be doing 60 mph.
Do aftermarket wheels need hub-centric rings on a 2016–2018 Ford Focus RS?
The 2016–2018 Ford Focus RS's hub bore is 63.4 mm. Wheels machined to exactly 63.4 mm center on the hub directly; wheels with a larger bore need 63.4 mm hub-centric rings to avoid vibration.
Also on 5x108
These share the bolt pattern. Check offset, hub bore and brake clearance before swapping wheels.
| Vehicle | Generation | Bolt pattern | Hub bore |
|---|---|---|---|
| 2013–2018 Ford Focus ST | Mk3 | 5x108 | 63.4 mm |