2005–2013 Chevrolet Corvette Wheel & Tire Fitment Guide
C6 generation, Base coupe. 5x120.65 bolt pattern, stock 18×8.5 ET56 on 245/40R18. Compare 2 popular upgrades or try your own size.
Specs
| Bolt pattern | 5x120.65 |
|---|---|
| Center bore | 70.3 mm |
| Lug thread | M12x1.5 |
| Reference trim | Base coupe |
| Stock wheel | 18×8.5 ET56 |
| Stock tire | 245/40R18 |
| Stock overall diameter | 25.72 in |
Calculator
Starts on the stock setup. Drag the sliders or load one of the popular upgrades below.
The small mark on each slider shows the current value. Type in the box for sizes outside the slider range.
Custom vehicle measurementsOptional
Measure with your current wheels on the car and the results below show how much room the new setup leaves. The drawings use your numbers too. Leave blank anything you haven't measured.
- Park on level ground at normal ride height, wheels straight.
- Front and rear differ. Measure the axle you're changing, or enter the tighter corner.
Millimetres or centimetres are recommended: small gaps are easier to read accurately than inch marks.
Narrowest gap between the inside of the tire (or wheel, whichever sits further in) and the strut, spring perch or upper control arm. Wheels pointed straight.
Hang a plumb line or hold a straightedge vertically from the fender lip above the hub, then measure across to the outermost point of the tire or wheel. Enter a negative number if it already sticks out.
Straight up from the top of the tire to the fender lip, with the car on the ground at normal ride height.
Smallest gap between the outer edge of the brake caliper and the inside of the wheel barrel.
- Poke
- 0mm
- Wheel face stays where it is.
- Inner clearance
- 0mm
- Same room to the suspension.
- Overall diameter
- 0%
- 0 in, within ±3%.
- Speedo reads 60
- 60mph
- Your actual speed.
| Vehicle | Chevrolet Corvette Base coupe | ||
|---|---|---|---|
| Bolt pattern | 5x120.65 | Hub bore | 70.3 mm |
| Current | 18×8.5 ET56, 245/40R18 | New | 18×8.5 ET56, 245/40R18 |
Popular upgrades
Each size compared with the stock 18×8.5 ET56, 245/40R18.
| Setup | Poke | Inner clearance | Diameter | Speedo reads 60 | Action |
|---|---|---|---|---|---|
| Flush 18×918×9 ET50, 255/35R18 | +12.4 mm | −0.4 mm | −2.7% | 58.4 mph | |
| C7 Z06-style 19×8.519×8.5 ET56, 245/35R19 | 0 mm | 0 mm | +0.1% | 60.1 mph |
Notes
- Staggered from the factory. Rear stock: 19×10 ET79 with 285/35ZR19.
- The very high factory offsets (+56 front, +79 rear) mean most aftermarket narrow-body wheels pair with hub-centric spacers or adapters (70.3 mm bore); owners running C7 Z06-style 19/20 reproductions used 20 mm hub-centric adapters.
- Narrow-body limits reported are about 9.5 in wide up front and 10.5–11 in at the rear (around 305 rear tire); Z06/Grand Sport widebody wheels (19×12 rear) don't suit the narrow base rear fenders.
- Ride height can be dropped on the factory leaf-spring adjuster bolts, which tightens fender clearance on wider setups.
Questions
What bolt pattern does a 2005–2013 Chevrolet Corvette use?
The 2005–2013 Chevrolet Corvette uses a 5x120.65 bolt pattern with a 70.3 mm center bore and M12x1.5 lug threads.
What size wheels and tires are stock on the 2005–2013 Chevrolet Corvette Base coupe?
The 2005–2013 Chevrolet Corvette Base coupe came with 18×8.5 ET56 wheels and 245/40R18 tires, about 25.7 inches in overall diameter.
How far does a 18×9 ET50 wheel stick out on a 2005–2013 Chevrolet Corvette?
On the 2005–2013 Chevrolet Corvette, compared with the stock 18×8.5 ET56, a 18×9 ET50 sits 12.4 mm further out at the outer lip and 0.4 mm closer to the suspension at the inner barrel.
Which 2005–2013 Chevrolet Corvette wheel and tire upgrade keeps the speedometer most accurate?
Of the 2005–2013 Chevrolet Corvette upgrades listed here, 19×8.5 ET56 · 245/35R19 is closest to the stock 245/40R18, changing overall diameter by +0.1%. At an indicated 60 mph you would actually be doing 60.1 mph.
Do aftermarket wheels need hub-centric rings on a 2005–2013 Chevrolet Corvette?
The 2005–2013 Chevrolet Corvette's hub bore is 70.3 mm. Wheels machined to exactly 70.3 mm center on the hub directly; wheels with a larger bore need 70.3 mm hub-centric rings to avoid vibration.
Also on 5x120.65
These share the bolt pattern. Check offset, hub bore and brake clearance before swapping wheels.
| Vehicle | Generation | Bolt pattern | Hub bore |
|---|---|---|---|
| 2001–2004 Chevrolet Corvette | C5 | 5x120.65 | 70.3 mm |
| 2014–2019 Chevrolet Corvette | C7 | 5x120.65 | 70.3 mm |