2001–2004 Chevrolet Corvette Wheel & Tire Fitment Guide
C5 generation, Z06. 5x120.65 bolt pattern, stock 17×9.5 ET54 on 265/40R17. Compare 2 popular upgrades or try your own size.
Specs
| Bolt pattern | 5x120.65 |
|---|---|
| Center bore | 70.3 mm |
| Lug thread | M12x1.5 |
| Reference trim | Z06 |
| Stock wheel | 17×9.5 ET54 |
| Stock tire | 265/40R17 |
| Stock overall diameter | 25.35 in |
Calculator
Starts on the stock setup. Drag the sliders or load one of the popular upgrades below.
The small mark on each slider shows the current value. Type in the box for sizes outside the slider range.
Custom vehicle measurementsOptional
Measure with your current wheels on the car and the results below show how much room the new setup leaves. The drawings use your numbers too. Leave blank anything you haven't measured.
- Park on level ground at normal ride height, wheels straight.
- Front and rear differ. Measure the axle you're changing, or enter the tighter corner.
Millimetres or centimetres are recommended: small gaps are easier to read accurately than inch marks.
Narrowest gap between the inside of the tire (or wheel, whichever sits further in) and the strut, spring perch or upper control arm. Wheels pointed straight.
Hang a plumb line or hold a straightedge vertically from the fender lip above the hub, then measure across to the outermost point of the tire or wheel. Enter a negative number if it already sticks out.
Straight up from the top of the tire to the fender lip, with the car on the ground at normal ride height.
Smallest gap between the outer edge of the brake caliper and the inside of the wheel barrel.
- Poke
- 0mm
- Wheel face stays where it is.
- Inner clearance
- 0mm
- Same room to the suspension.
- Overall diameter
- 0%
- 0 in, within ±3%.
- Speedo reads 60
- 60mph
- Your actual speed.
| Vehicle | Chevrolet Corvette Z06 | ||
|---|---|---|---|
| Bolt pattern | 5x120.65 | Hub bore | 70.3 mm |
| Current | 17×9.5 ET54, 265/40R17 | New | 17×9.5 ET54, 265/40R17 |
Popular upgrades
Each size compared with the stock 17×9.5 ET54, 265/40R17.
| Setup | Poke | Inner clearance | Diameter | Speedo reads 60 | Action |
|---|---|---|---|---|---|
| OEM+ 18×1018×10 ET58, 275/35R18 | +2.4 mm | −10.4 mm | +0.9% | 60.5 mph | |
| Track square 18×1118×11 ET57, 315/30R18 | +16 mm | −22.1 mm | +0.4% | 60.2 mph |
Notes
- Rear stock: 18×10.5 ET58 with 295/35R18; the Z06 runs 17-inch fronts with 18-inch rears.
- The bolt pattern is 5x4.75 in (5x120.65), not 5x120, so Camaro/BMW 5x120 wheels are not a safe swap; lug nuts are M12x1.5 on a 70.3 mm hub.
- The bolt-on 18×10 ET58 front is paired with an 18×11 ET57 rear (315/30R18) or 19×11 ET57 rear (305/30R19).
- Square 18×11 ET57 with 315/30R18 on all four corners is a hardcore track setup that needs light modifications.
Questions
What bolt pattern does a 2001–2004 Chevrolet Corvette use?
The 2001–2004 Chevrolet Corvette uses a 5x120.65 bolt pattern with a 70.3 mm center bore and M12x1.5 lug threads.
What size wheels and tires are stock on the 2001–2004 Chevrolet Corvette Z06?
The 2001–2004 Chevrolet Corvette Z06 came with 17×9.5 ET54 wheels and 265/40R17 tires, about 25.3 inches in overall diameter.
How far does a 18×11 ET57 wheel stick out on a 2001–2004 Chevrolet Corvette?
On the 2001–2004 Chevrolet Corvette, compared with the stock 17×9.5 ET54, a 18×11 ET57 sits 16 mm further out at the outer lip and 22.1 mm closer to the suspension at the inner barrel.
Which 2001–2004 Chevrolet Corvette wheel and tire upgrade keeps the speedometer most accurate?
Of the 2001–2004 Chevrolet Corvette upgrades listed here, 18×11 ET57 · 315/30R18 is closest to the stock 265/40R17, changing overall diameter by +0.4%. At an indicated 60 mph you would actually be doing 60.2 mph.
Do aftermarket wheels need hub-centric rings on a 2001–2004 Chevrolet Corvette?
The 2001–2004 Chevrolet Corvette's hub bore is 70.3 mm. Wheels machined to exactly 70.3 mm center on the hub directly; wheels with a larger bore need 70.3 mm hub-centric rings to avoid vibration.
Also on 5x120.65
These share the bolt pattern. Check offset, hub bore and brake clearance before swapping wheels.
| Vehicle | Generation | Bolt pattern | Hub bore |
|---|---|---|---|
| 2005–2013 Chevrolet Corvette | C6 | 5x120.65 | 70.3 mm |
| 2014–2019 Chevrolet Corvette | C7 | 5x120.65 | 70.3 mm |