2021+ Ford F-150 Raptor Wheel & Tire Fitment Guide
3rd gen (P702) generation, Base (35-inch tire package). 6x135 bolt pattern, stock 17×8.5 ET34 on 315/70R17. Compare 2 popular upgrades or try your own size.
Specs
| Bolt pattern | 6x135 |
|---|---|
| Center bore | 87.1 mm |
| Lug thread | M14x1.5 |
| Reference trim | Base (35-inch tire package) |
| Stock wheel | 17×8.5 ET34 |
| Stock tire | 315/70R17 |
| Stock overall diameter | 34.36 in |
Calculator
Starts on the stock setup. Drag the sliders or load one of the popular upgrades below.
The small mark on each slider shows the current value. Type in the box for sizes outside the slider range.
Custom vehicle measurementsOptional
Measure with your current wheels on the car and the results below show how much room the new setup leaves. The drawings use your numbers too. Leave blank anything you haven't measured.
- Park on level ground at normal ride height, wheels straight.
- Front and rear differ. Measure the axle you're changing, or enter the tighter corner.
Millimetres or centimetres are recommended: small gaps are easier to read accurately than inch marks.
Narrowest gap between the inside of the tire (or wheel, whichever sits further in) and the strut, spring perch or upper control arm. Wheels pointed straight.
Hang a plumb line or hold a straightedge vertically from the fender lip above the hub, then measure across to the outermost point of the tire or wheel. Enter a negative number if it already sticks out.
Straight up from the top of the tire to the fender lip, with the car on the ground at normal ride height.
Smallest gap between the outer edge of the brake caliper and the inside of the wheel barrel.
- Poke
- 0mm
- Wheel face stays where it is.
- Inner clearance
- 0mm
- Same room to the suspension.
- Overall diameter
- 0%
- 0 in, within ±3%.
- Speedo reads 60
- 60mph
- Your actual speed.
| Vehicle | Ford F-150 Raptor Base (35-inch tire package) | ||
|---|---|---|---|
| Bolt pattern | 6x135 | Hub bore | 87.1 mm |
| Current | 17×8.5 ET34, 315/70R17 | New | 17×8.5 ET34, 315/70R17 |
Popular upgrades
Each size compared with the stock 17×8.5 ET34, 315/70R17.
| Setup | Poke | Inner clearance | Diameter | Speedo reads 60 | Action |
|---|---|---|---|---|---|
| 37s on stock 17×8.517×8.5 ET34, 315/80R17 | 0 mm | 0 mm | +7.2% | 64.3 mph | |
| 17×9 +12 with 37s17×9 ET12, 315/80R17 | +28.4 mm | +15.6 mm | +7.2% | 64.3 mph |
Notes
- Stock tire is a 35-inch BFGoodrich KO2 (LT315/70R17), the same size front and rear on 17×8.5 ET34 wheels. The 37s upgrades use 37x12.50R17, shown here as its closest metric equivalent, 315/80R17.
- The 37-inch package uses forged 17×8.5 wheels at ET30, about 4 mm further out than the ET34 cast and beadlock-capable wheels on 35-inch trucks.
- Owners report factory 37-inch KO2s fit a 35-inch truck on stock wheels and stock suspension without rubbing, and 37x12.50R17 KO2s on 17×9 +12 wheels also cleared. Heavier or wider 37s may rub.
- Uses M14x1.5 lug nuts on the 6x135 / 87.1 mm hub, the same as 2015+ F-150s; the wheels are hub-centric.
Questions
What bolt pattern does a 2021+ Ford F-150 Raptor use?
The 2021+ Ford F-150 Raptor uses a 6x135 bolt pattern with a 87.1 mm center bore and M14x1.5 lug threads.
What size wheels and tires are stock on the 2021+ Ford F-150 Raptor Base (35-inch tire package)?
The 2021+ Ford F-150 Raptor Base (35-inch tire package) came with 17×8.5 ET34 wheels and 315/70R17 tires, about 34.4 inches in overall diameter.
How far does a 17×9 ET12 wheel stick out on a 2021+ Ford F-150 Raptor?
On the 2021+ Ford F-150 Raptor, compared with the stock 17×8.5 ET34, a 17×9 ET12 sits 28.4 mm further out at the outer lip and 15.6 mm further from the suspension at the inner barrel.
Which 2021+ Ford F-150 Raptor wheel and tire upgrade keeps the speedometer most accurate?
Of the 2021+ Ford F-150 Raptor upgrades listed here, 17×8.5 ET34 · 315/80R17 is closest to the stock 315/70R17, changing overall diameter by +7.2%. At an indicated 60 mph you would actually be doing 64.3 mph.
Do aftermarket wheels need hub-centric rings on a 2021+ Ford F-150 Raptor?
The 2021+ Ford F-150 Raptor's hub bore is 87.1 mm. Wheels machined to exactly 87.1 mm center on the hub directly; wheels with a larger bore need 87.1 mm hub-centric rings to avoid vibration.
Also on 6x135
These share the bolt pattern. Check offset, hub bore and brake clearance before swapping wheels.
| Vehicle | Generation | Bolt pattern | Hub bore |
|---|---|---|---|
| 2017–2020 Ford F-150 Raptor | 2nd gen | 6x135 | 87.1 mm |