2015–2023 Dodge Challenger Wheel & Tire Fitment Guide
LA generation, R/T (narrow-body). 5x115 bolt pattern, stock 20×8 ET24 on 245/45R20. Compare 3 popular upgrades or try your own size.
Specs
| Bolt pattern | 5x115 |
|---|---|
| Center bore | 71.5 mm |
| Lug thread | M14x1.5 |
| Reference trim | R/T (narrow-body) |
| Stock wheel | 20×8 ET24 |
| Stock tire | 245/45R20 |
| Stock overall diameter | 28.68 in |
Calculator
Starts on the stock setup. Drag the sliders or load one of the popular upgrades below.
The small mark on each slider shows the current value. Type in the box for sizes outside the slider range.
Custom vehicle measurementsOptional
Measure with your current wheels on the car and the results below show how much room the new setup leaves. The drawings use your numbers too. Leave blank anything you haven't measured.
- Park on level ground at normal ride height, wheels straight.
- Front and rear differ. Measure the axle you're changing, or enter the tighter corner.
Millimetres or centimetres are recommended: small gaps are easier to read accurately than inch marks.
Narrowest gap between the inside of the tire (or wheel, whichever sits further in) and the strut, spring perch or upper control arm. Wheels pointed straight.
Hang a plumb line or hold a straightedge vertically from the fender lip above the hub, then measure across to the outermost point of the tire or wheel. Enter a negative number if it already sticks out.
Straight up from the top of the tire to the fender lip, with the car on the ground at normal ride height.
Smallest gap between the outer edge of the brake caliper and the inside of the wheel barrel.
- Poke
- 0mm
- Wheel face stays where it is.
- Inner clearance
- 0mm
- Same room to the suspension.
- Overall diameter
- 0%
- 0 in, within ±3%.
- Speedo reads 60
- 60mph
- Your actual speed.
| Vehicle | Dodge Challenger R/T (narrow-body) | ||
|---|---|---|---|
| Bolt pattern | 5x115 | Hub bore | 71.5 mm |
| Current | 20×8 ET24, 245/45R20 | New | 20×8 ET24, 245/45R20 |
Popular upgrades
Each size compared with the stock 20×8 ET24, 245/45R20.
| Setup | Poke | Inner clearance | Diameter | Speedo reads 60 | Action |
|---|---|---|---|---|---|
| Scat Pack 20×920×9 ET22.5, 245/45R20 | +14.2 mm | −11.2 mm | 0% | 60 mph | |
| SRT-style 20×9.5 square20×9.5 ET18.5, 275/40R20 | +24.5 mm | −13.5 mm | −0.1% | 60 mph | |
| Wide 20×10 square20×10 ET19, 275/40R20 | +30.4 mm | −20.4 mm | −0.1% | 60 mph |
Notes
- Scat Pack cars came on 20×9 ET22.5 wheels with 245/45R20, and the SRT 392 on half-inch-wider 20×9.5 wheels with 275/40R20, so both sizes fit a narrow-body car.
- Apex lists a square 20×10 ET19 with 275/40R20 as a direct fit on narrow-body Challengers.
- Shares 5x115, a 71.5 mm hub bore and M14x1.5 lug nuts with the Charger and Chrysler 300, so wheels cross over when offset and brake clearance match.
- Widebody cars (2018+) run 20×11 wheels at near-zero offset; this guide covers narrow-body cars only.
Questions
What bolt pattern does a 2015–2023 Dodge Challenger use?
The 2015–2023 Dodge Challenger uses a 5x115 bolt pattern with a 71.5 mm center bore and M14x1.5 lug threads.
What size wheels and tires are stock on the 2015–2023 Dodge Challenger R/T (narrow-body)?
The 2015–2023 Dodge Challenger R/T (narrow-body) came with 20×8 ET24 wheels and 245/45R20 tires, about 28.7 inches in overall diameter.
How far does a 20×10 ET19 wheel stick out on a 2015–2023 Dodge Challenger?
On the 2015–2023 Dodge Challenger, compared with the stock 20×8 ET24, a 20×10 ET19 sits 30.4 mm further out at the outer lip and 20.4 mm closer to the suspension at the inner barrel.
Which 2015–2023 Dodge Challenger wheel and tire upgrade keeps the speedometer most accurate?
Of the 2015–2023 Dodge Challenger upgrades listed here, 20×9 ET22.5 · 245/45R20 is closest to the stock 245/45R20, changing overall diameter by 0%. At an indicated 60 mph you would actually be doing 60 mph.
Do aftermarket wheels need hub-centric rings on a 2015–2023 Dodge Challenger?
The 2015–2023 Dodge Challenger's hub bore is 71.5 mm. Wheels machined to exactly 71.5 mm center on the hub directly; wheels with a larger bore need 71.5 mm hub-centric rings to avoid vibration.
Also on 5x115
These share the bolt pattern. Check offset, hub bore and brake clearance before swapping wheels.
| Vehicle | Generation | Bolt pattern | Hub bore |
|---|---|---|---|
| 2015–2023 Dodge Charger | LD | 5x115 | 71.5 mm |